Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
nRF52832 custom board + NCS 3.0.1
We are using the Zephyr driver for LIS2DH sensor in "any motion" detection mode, which triggers an interrupt when acceleration exceeds...
Hello,
I'm evaluating the nPM1300 for a battery powered project. What is the quiescent current of the LDO? And is there an output current vs dropout chart?
Thanks
Hi, Using NCS 3.0.0 it would appear that the function sntp_simple_helper does not work with SYS_FOREVER_MS as a timeout value.
Problem: When we pass this value as a timeout...
Hi,
I want BLE and ZIGBEE to be able to switch dynamically during running.Only one mode(BLE or ZIGBEE) is running at a time.If switching from zigbee to BLE, how do I turn...
I have implemented DFU functionality in my Bluetooth mesh project and used device A as the distributor and device B as the node to be updated. I have already configured both...
We have our firmware developed with ncs2.7.0 and everything works as expected. However, with a recent effort of moving to ncs2.9.1, the same project can be built but during...
When calling the bt_conn_le_create_synced function to create a connection to a peripheral, which is synced to the PAwR train, I get a CONNECTION FAILED TO BE ESTABLISHED ...
We are trying to increase the TX output power on the nRF5340 when using Enhanced ShockBurst (ESB) . According to the product specification, the nRF5340 supports +3 dBm TX...
Hello
I'm currently working on writing some specifications for a future product. In this product, I want to use the advertising mechanism to send specific data from one...
Hello,
I recently acquired a Thingy91 board in order to make a hardware prototype. I already have experience developing with the nRF52840 so I took inspiration from my working...
we don't seem to have power numbers for the 54L, but in the 5340 datasheet it shows the LFXO (0.16uA) used less power then the LFRC (1 uA).
Is that true with the NRF54L...
Hello, I am working on a project using a custom hardware configuration based on nRF5340 and nRF7002 similar in configuration to the nRF7002-DK, except without the on-board...
Hi!
We're building a project for the nRF54 where we want to run an external library on the FLPR core.
Right now we have a prototype PCB with a module from Fanstel on it...
Hello,
I am using configUSE_TICKLESS_IDLE with RTC2 setup for FreeRTOS tick, occasionally I am seeing the asserting in task.c at line configASSERT( ( xTickCount + xTicksToJump...