Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
Hi,
How many SPI slaves can I connect to nRF52832 as an SPI master?
I would like to know the maximum number of SPI slaves which can be connected to nRF52832 as an SPI...
Hello all,
According to the documentation and this feedback on a case there is a maximum size for a particular cert before nrf_inbuilt_key_write returns NRF_ENOBUFS . Can...
Hi,
I am using NRF52832 for development without bluetooth SDK, NFC and RTC.
I am using a development board with SPI and a slave device that can communicate normally (using...
Hello,
Most of the outputs and LTE Monitor use by defaut an UART on DK. Problem on custom boards, for cost limitation, UART is not always present. Probe connector is so...
irq init as below:
I use port event, and muti-gpio irqs. Irq gpio connect a sensor`s irq pin.
I detect irq gpio level in irq_Handler(), high level is my need, the...
Hello All.
I Need help ... first time use "nRF52840"
Goal of this project is "record voice with digital mems mic and play that voice using speaker with i2s"
First...
Searching through the forum I found this guide.
"Getting started with Nordic's Secure DFU bootloader, a step by step guide"
https://devzone.nordicsemi.com/nordic/nordic...
SDK 16.0.0
nRF52DK
ble_app_hts example
The ble_srv_is_indication_enabled always return false no matter in the ble_hts_is_indication_enabled function or in the on_cccd_write...
Hi, im usinh SDK V 15.3
i was following the tutorial to add buttonless dfu to my application code
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hello,
I am a newbie and need some help deciding the path to perform the following requirement. Any help is appreciated.
Requirement:
I have Rigado BMD-350 module currently...
Hi,
I have a nRF52840 DK (PCA10056 v0.9.0). I tried the long range (Coded PHY) but it throws an error and didn't work. I read in nordic forums that the chip revision should...
We are entering a pre-production phase where the contract manufacturer must program dozens of nRF9160 modules, and we would like to offer a command-line method, to simply...
I've just got my toolchain working fine but there's now errors relating to the correct libraries being included. Do I have to have these included by running a "west update...
I use 3.10 mesh sd and 2 dk boards.
DFU example works fine, but when I try to implement dfu mode in ls example I can't achieve goal. DFU doesn't work. I follow the instruction...
