Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Anyone here have experience of going through FCC / CE certifications ?
We had a UK based company give us a rough cost but that quadrupled when they provided a final price...
Hello All,
Recently, I started working with nrf9160 and found it uses Zephyr for building application. Can anyone suggest me a any good tutorials for learning Zephyr from...
Hi I am following the instruction in the following link to do a open DFU through USB UART:
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started...
We're experiencing occasional unexpected hardware watchdog resets. The watchdog is set to 10 minutes, and sometimes just 2 minutes after feeding the WDT we see a reset triggered...
Hi there,
I'm currently developing a ble mesh network for the Thingy 52. I'm accesing the temperature and humidity sensor but I need the firmware code of the Thingy 52...
Having problems bootloading my own application on my hardware. The application runs fine alone. Using SDK 16.0 and secure_bootloader/pca10056_uart example via Segger SES....
Hello,
anyone with with knowledge on how to control the gpio pins of the NRF 9160 SiP?
In my scenario, I am using P0.01 - P0.12 as digital control signals, for "Enableing...
Hi Nordic
For mesh-sdk-4.0 examples/light_switch/server, how many LPN can a server to establish friendship?
Is it limited to MESH_FRIEND_FRIENDSHIP_COUNT?
Regards...
Hi, I have custom nRF52832QFAAE1 when I tried to run Peripheral applications which are working fine. whereas BLE applications are not running it seems.
here are the things...
Hello,
When I clean a project and do a new build, parallel settings looks wring (my AMD ryzen 3900X with 12 cores never use more than 40 %).
Do someone have a setting...
Currently, we are testing the nRF52840 range evaluation using the nRF52840 EVK kit.
As of now, we are getting the only 120 to 125-meter range using 125kbps data rate @ 4dBM...
Hello.
I found in Provisioing chapter on this document: https://www.bluetooth.com/specifications/mesh-specifications/
something like list of provisioning commands: ...
Hello.
I plan to perform antenna matching to improve the performance of my design.
I would like to know any differences when performing the match on bare pcb and pcb...
Hi,
I'm working on a test for the pulse width measurement, the input is analog signal.
I'm using a while loop, and use nrfx_comp_sample in the loop to get the voltage...
