Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I have a problem while provisioning the dongles in a mesh network, which is faced by most of the people around. Right now I'm using the latest mesh sdk. Can you help me with...
I'm having trouble reading value from ADC. What I want is to read a sample and not set any timer, since I want to run it inside a timer itself and have the refreshed value...
I have designed a custom board using nRF52832. As per my understanding, we can configure any GPIO pin for UART communication. However, I am not able to configure the board...
Hello,
I am running into an issue attempting to add certificates to the device in order to facilitate HTTPS calls to our backend directly from the device.
Before the LTE...
Hi all,
I am trying make some temperature sensor with Segger and nRF52 based on Mesh BLE v4.0.
Currently I am researching documentation and examples to pick best solution...
I'm trying to use the information from this devpost: https://devzone.nordicsemi.com/f/nordic-q-a/39629/how-to-send-data-to-all-node-over-mesh
However, my remaining questions...
I would like to see an example or documentation about how to set my nRF52 DK into various sleep modes. I know that calling "sd_power_system_off()" will turn the device into...
Hello how are you?
I don't speak English very well but I have a doubt about using mesh and nfc simultaneously.
I'm using the Nordic-Thingy52-mesh-demo example - (Nordic...
Hi, team
I am using nRF5_SDK_15.3.0_59ac345/examples/ble_peripheral/ble_app_ancs_c sample application. and i wnated to add extra notification attribute.
added BLE_ANCS_KEY1...
As I understand from documentation current limit for nRF PPK is 70mA. This is when PPK automatically sets measurement range from 1 o 70mA. My question is: Is there a way to...
1、Demo position：Nordic\nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ble_app_uart\pca10056
2、I find when the code execute the function of timer_start_op_schedule,the CRITICAL_REGION_ENTER...
Hello,
Using this link ( https://devzone.nordicsemi.com/f/nordic-q-a/35675/how-to-use-static-passkey-for-a-no-display-no-output-peripheral ) I'm able to add passkey protection...
Hi,
i have found similar posts on the forum but could not find the answer. Therefore,I think it is necessary to raise this question again.
problem: platform:nRF52832 and...
Hello there,
I have been testing on nfc-uart example of SDK 13.3.0. I am trying to pass the buffer of 258 bytes to pointer "p_pdu" and its size of 258 to "pdu_lenght". ...
