Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi,
I have two questions:
1) After requesting PSM mode (assuming the MNO supports PSM mode for NB-IoT) and afterwards enabling GPS, does the GPS automatically detects...
Hi,
I am currently working on the development of a customized Tracker application. I was testing one use case where the Tracker definitely not being able to achieve a GPS...
Hello,
I'm using BT840XE module and ATT_MTU Throughput Example with S140. My goal is to measure maximum data transfer speed between module and different phones. Module acts...
Hi,
I'm using nrf52832 (SDK 15.3). And I have 24 chips on the same I2C bus. They all work fine right row. But if one of the chip is broken, the whole system will crash....
If a reliable mesh transfer is ongoing the node will crash with a mesh assert at access_reliable.c:373, in access_reliable_cancel_all().
This happens because access_clear...
Hi all,
I am looking for the Objective Product Specification for the nRF52840 chip. I have only found the Objective P roduct Specification for nRF52832 in version 0.6.3...
After setting up my Peripheral Mode I am also looking at ways to improve my current design. I would like to ask about Mesh support on the NRF Thingy 91 integrated with the...
Was anybody able to connect to HTS (Health Thermometer Service) on iOS applications, OTHER than nRFToolbox or LightBlue? Which applications did you use?
I tried a dozen...
Greetings....
It is great that you provided SDK UART coexistence example for nRF5 SDK for Mesh v3.1.0 and nRF5 SDK v15.2.0 release for Client node with nRF52832 DK. However...
I am trying to build an example code for PCA10040, but I always have a lot of compiler error: C:/Program Files (x86)/SEGGER/SEGGER Embedded Studio for RISC-V 4.42/source/thumb_crt0...
Hello,
I'm working with the Nrf52832 Dev Kit and the ble_uart_example. After flashing with the hex file and powering the Dev Kit, the on-board-LED starts to blink. Now I...
Hi Nordic team,
I am currently developing a concurrent wireless application with BLE and a proprietary protocol using the timeslot API.
My setup:
nRf52840 DK
SDK...
Hello, guys!
We are working with SDK 15.0.0 and nRF52840 SoCs.
There is a need to transfer a few MBytes of data from the PC to nRF52840 and then on external flash memory...
Hi
this is the code I'm trying with my buzzer,
I want it to generate sound but with different frequencies.
".base_clock = NRF_PWM_CLK_1MHz," I can only as low as 125kHz...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). I am trying to combine the examples ble_app_uart...
