I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hi
I m using NRF52832 for beacon application.In my application, the device should be in the system off mode .After holding button for 5 secs, the system will back to idle...
Hi
I'm using SDK version15.2 and SD on a custom board based on nRF52840.
The board has two serial ports, and I want to use both independently. Using the Serial Port Library...
Hi Nordic Team,
My requirement is-
Advertise -> Connect to 1 device -> Send packet -> Disconnect -> Delay(1min) -> Advertise -> Connect to 2 device...
I am using Timer...
I am using nrfMeshProvision cocoapod to create a Mesh Network using a iOS Mobile application. In first step of identifying the device, i am able to call bearer.open() and...
Hi,
I've used the nRF connect 'Getting Started' software and tutorial to setup a development environment, however i am having problems with the "Set up a project in SEGGER...
Hi Nordic Team,
Please share a logic to filter with address for connection over BLE. Please help as soon as possible.
Thanks & Regards,
Aswati Vijaykumar
Hi
I am currently developing a demo application and started with the ble_app_template project from the ble_peripheral_folder (s140 softdevice, sdk 16.0). I copied it to...
I am using a module called Core51822 which includes NRF51822, with the NRF51822 Evaluation kit and the ST Link to program it from Arduino IDE.
I want basically to program...
can someone suggest me some tutorials how to do programming in nrf52840 from scratch.
i have tried some examples like blink an led just like opening the file and running...
Hallo devzone,
i have a real time task, where i have a trigger, different calculations and then the corresponding action.
Now i need to calculate the time from the trigger...
Hello,
As I am new to the world of bluetooth and its stack I have a question which I cannot find the answer for on the internet.
I've read a ton of posts on the devzone...
Hi Nordic Team,
Requirement-
Connect->Send 1 packet->Disconnect->Connect...
I am Sending a data packet to central using Timer handler and trying to disconnect using...
Good day.
I am trying to add flash storage functionality to a project based on the ANT asynchronous transmitter example and the ANT back ground channel example of the SDK...
I am using the nRF51822 QFAAH0 Chip and running it on 90 mAh battery. Currently I am using the AMS1117 3.3v LDO voltage regulator. It is running as iBeacon for 7 hours. I...
Hello Sir,
I am developing nRF9160 based smart tracking device for kids , and i am used only nrf9160 not used nrf52840. so my problem is that how to upload firmware direct...
