I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hello,
I can't get the hex file to come out correctly in segger studio. What happens is, I build the solution and create the hex file but when I go to program my device...
Environment - nrf52832 - SDK 15.3
- SD 6.1.1 - with FreeRTOS
- Project: ble_app_buttonless_dfu
I have project with 4 timers and 3 tasks. Everything works fine when...
I have made changes from here in order to configure data rate at Coded PHY for mesh application.
Tested with two phones: Moto G5 Plus (Bluetooth 4.2) OnePlus 6 (Bluetooth...
Hi,
I am tring to display some information using NRF_LOG_HEXDUMP_DEBUG(). However, I can't see anything on the terminal. If I use NRF_LOG_INFO("xxxxx"), I can see the...
I'm using two nRF52840 DKs with SDK 16.0 with one as a central, the other as a peripheral. I'd like to setup an IRK whitelist on the peripheral. I've taken a look at the hid...
Hello,
I'm having trouble getting my program to compile with the SAADC. I started with a BLE template then added the battery service with sensorsim from ble_app_hrs and...
Hi.
I am trying to use nrf52840 on a custom board and configure it as spi slave, and an STM32H7 controller would be the master. I am using the spis example for nrf. I...
Hi guys,
I would like to know which pins of my MAX30102 Heart rate module connect to my nrf52832 SoC and where do they connect to on the chip?
Do the SCL and SDA pins...
Hi i am trying to reduce the adc read times to a minimum we currently have it setup for 3us acq and 32 samples so expecting something close to 160us Its getting around 250us...
Hi,
I'm trying to implement nrfutil serial DFU master in C code. I have few doubts on it.
1. Can we avoid ping packet at the start?
2. What is PNR and how we can...
Hi i'm trying to execute a code, but during the compilation it gives me a bug. The bug happens when I pressed a Button that has been programmed to restart the Ublox module...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
I want to recover after fatal error...
To the kind attention of Nordic support team,
reading this https://devzone.nordicsemi.com/f/nordic-q-a/39630/windows-command-line-dfu-over-ble-with-pca10059 thread,
I...
Hi, I'm using the Cyclone FX programmer to program our custom boards with the NRF52840 chip, but after programming all the hex files, the application starts straightaway bypassing...
