Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello everyone, just a quick question.
When routing on the nrf52832 WLCSP package, I noticed that the only inner pin "required" for use is the pin to enable DC/DC (Pin B6...
Hey guys,
I want to create an accurate timer without interrupts. My timer has to be very accurate because I have to send HIGH and LOW signals for 1us. I have read this pos...
Hello.
Currently I am trying to merge the peripheral example ble_uart and saadc examle. My little project is to send potentiometer values over ble.
As of now I have copied...
I have the bmdware.uvprojx project opened in Keil uVision 5 and have the BMD 350 breakout board containing the nRF52832 chip connected to my PC via a J Link debugger (EDU...
Hi all,
Here I am using the nrf52840 in my customized board, in parallel i have nrf52840 dev board.
I am using the twi peripheral to communicate with a i2c based sensor...
Hey,
I am using SDK16 and want to update the bootloader on my NRF52840 from SDK15 with a new one.
I modified the bootloader from SDK16 a little bit. Then I created a Zip...
To the kind attention of Nordic support team,
I have got in here two pictures of flash. The first one it is after installing bootloader and settings, softdevice and application...
Hi,
I am working on a product development that uses an nRF52832 (through a LAIRD BL-652 module).
We have a voltage point (named 5V), that is connected to SIO_28 GPIO through...
Dear,
I used ncs_v1.0.0_joakim to adapt the battery of my thingy91:
I used: battery_monitor_read(); to read the %battery, and it worked well
I just updated new...
I understand correctly that in order to use my private key for my applications, I must first sign an immutable bootloader with this key and upload it to the device?
I used...
Hello there,
It seems the CC310 backend for ChaChaPoly does not allow zero-length data or adata (associated data). I am implementing a protocol that requires this (Wireguard...
I am trying to change the default ATT_MTU size from 23 to 64.
my code uses Ble_nus service and Eddystone_Service.
Eddystone service is in connectable mode and it's where...
Env.: nRF52 customBoard, SES, nRF5_SDK_16.0.0_98a08e2
Hi,
I'am working with ble_app_template example and currently trying, to merge it with the experimental multiperipheral...
I have added an external SPI flash on the nRF9160 DK board, and wired it up to SPI3. I want to partition the flash into two ares for separate uses, but the partition_manager...
Hello.
I have just recived my nrf5340 PDK. I started with the hear rate example programming with the console. With some troubles but finally it worked.
Now I'm trying...
