We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi all,
I am trying make some temperature sensor with Segger and nRF52 based on Mesh BLE v4.0.
Currently I am researching documentation and examples to pick best solution...
I'm trying to use the information from this devpost: https://devzone.nordicsemi.com/f/nordic-q-a/39629/how-to-send-data-to-all-node-over-mesh
However, my remaining questions...
I would like to see an example or documentation about how to set my nRF52 DK into various sleep modes. I know that calling "sd_power_system_off()" will turn the device into...
Hello how are you?
I don't speak English very well but I have a doubt about using mesh and nfc simultaneously.
I'm using the Nordic-Thingy52-mesh-demo example - (Nordic...
Hi, team
I am using nRF5_SDK_15.3.0_59ac345/examples/ble_peripheral/ble_app_ancs_c sample application. and i wnated to add extra notification attribute.
added BLE_ANCS_KEY1...
As I understand from documentation current limit for nRF PPK is 70mA. This is when PPK automatically sets measurement range from 1 o 70mA. My question is: Is there a way to...
1、Demo position：Nordic\nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ble_app_uart\pca10056
2、I find when the code execute the function of timer_start_op_schedule,the CRITICAL_REGION_ENTER...
Hello,
Using this link ( https://devzone.nordicsemi.com/f/nordic-q-a/35675/how-to-use-static-passkey-for-a-no-display-no-output-peripheral ) I'm able to add passkey protection...
Hi,
i have found similar posts on the forum but could not find the answer. Therefore,I think it is necessary to raise this question again.
problem: platform:nRF52832 and...
Hello there,
I have been testing on nfc-uart example of SDK 13.3.0. I am trying to pass the buffer of 258 bytes to pointer "p_pdu" and its size of 258 to "pdu_lenght". ...
We would like to have that all communications, programming, and supply related TPs and SBs should be kept for debug purposes. Otherwise, we would like to remove all unnecessary...
We're working with the NRF5340 PDK, and it's a pretty big library change from the old SDK. So far I've been unable to find out where to configure the bluetooth PHY and link...
Hi everyone,
The task is as follows. I set up data transfer using notification. I transmit ~ 83 kB in ~ 10 sec. The connection interval parameters are as follows:
The...
Hi Guys,
I flashed the ble_app_uart example available in nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_uart\pca10056\s140\ses location to NRF52840 DK board. In...
