Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
So we are creating a peripheral with a characteristic meant to keep the central synced with the state of our peripheral. The peripheral is running all the time, could be ON...
1. This is on the stock LPN example, with one change to debug-print `status_code` inside handle_appkey_add().
Here is the diff:
2. To reproduce:
- flash and provision...
Hello,
I am currently working on a product with nRF51822 chip, based on SDK10.0.0. The problem is, after a firmware update, my device fails to reconnect to an Android mobile...
Hi,
I've launched wireshark + nRF52 Dongle successfully and I'm also able to select my device (named EWAT AI-No) from the list to sniff. However there's something I don...
I'm working on a simple project based on the USB CDC ACM and libuarte example, the chip is nrf52840.
A function is redirect the USB VCP data to another MCU via UART, just...
Can a server and a client of dimming example, have same element instead of different element ID.
I got worked for server and client model in single node, but they are in...
I am upgrading to SDK 15.3.0 and SoftDevice v6.1.1 from SoftDevice v2.0.0 (S332 stack). Most of functionality has been ported (BLE and ANT) and validated. This particular...
Hi, I'm trying using a setup with transmitter based on nRF24L01P and receiver with nRF24LU1P using Enhached Shock Burst. The problem is the transmission lock (three failed...
Hi,
I am planning system with a BLE peripheral (using nRF52840) and BLE Central (using nRF52840) that is AC powered.
The peripheral will be advertising every ~300msec...
Greetings,
We have some custom boards/devices with nrf9160. They each hold certificates to communicate with aws-iot. The certificates were flashed using the at_client...
Dear nordic,
I am developing a robot controller(Central, nRF51822).
However, I am having a problem with UUID.
And I am using the ble_central (s130 ble_app_uart...
Hi,
I am using nrfutil to generate a bootloader ota package for NRF52832 soic. The command I am using is
I measure on my ubuntu pc, when this command is...
When I was running the heart rate example, I would report this error below, someone tell me what caused this error, which causes the driver to fail to recognize now. But I...
Hello,
The project I'm working in will be using the nrf52840-devkit to create an application which utilizes the on board radio for communication. We will be using nrf connect...
Hi
Hopefully a quick question. I want to send a set of bytes 'shtpData' between to routines but only one byte is being sent:
Sending 'unit8_t *dataPacket' of 5 bytes....
