Hi,
I'm using the nRF52833 to develop a BLE beacon and built a Bluetooth gateway for my application.
Application Requirements:
The beacon should advertise using...
Hello,
I want to perform some antenna measurements and compare the rf performance of my custom PCB with an nrf9160 SiP with the nrf9160 dk.
To perform some antenna measurements...
Hello - I have the exact same question as proposed in this thread - I am wondering if there has been any change in the 3 last years since it was posted.
In a nutshell, we...
Hi I want to build a multi role BLE device.
As a peripheral it shall stream ADC data with arounf 20 kbytes per second.
As Central it shall receive adv_nonconn_ind packets...
Hello everyone,
I have an nRF5340 microcontroller (NORA B106 module), and I want to connect a square wave signal to one of its pins to read its frequency or count the number...
Hi,
Hope you are doing well.
I would like to use eSIM on nRF9151-DK board and an eSIM has been assembled in the board. However, eSIM is not detected.
According to...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
I'm getting the multi-link example working (device manager) with S130 SD and I noticed that the following define is in S110 and S120 but not in S130. I'm looking in the SDK8...
I've create a custom service with two characteristics. I need that the values of these characteristics are notifying at the same time. Is it possible? In this case, one of...
Peripheral role blue-tooth device, linked one phone.How to get phone address? such as phone's bluetooth mac address or something like that.Thank you!
note: device use softdevice...
Hello everyone,
I wanted to change the notification to indication for the BLE UART example when you send the message. I am currently using (and the UART BLE example is...
first sorry for my english, i work base on "ble_app_alert_notification->S110", i want to Enable Printf with uart,,,,but after i define maco ENABLE_DEBUG_LOG_SUPPORT,, 2 error...
hi all:
I want use nrf51822 to connect the some other sensor such as 90fity intelligent basketball, and discovery the service, and notify the character.
but the data...
www.microsoft.com/.../universal-foldable-keyboard
Why microsoft BT keyboard have 3 mode to support IOS, Android, Windows?
But we only have 1 sample for HID_keyboard.
Can...
HI：
I found a amazing problem:My flash project is ok,and my BLE project is ok too; But when i need to write data to flash,the BLE can't work any more.
code as follow:
all_init...
I'm using nRF51 SDK 6.0.0 and wanted to know when an "advertisement packet received" event is posted to the application. It looks like within a scan window only one such event...
Hi there,
I just ordered a nRF52 Preview DK and was wondering if this series will also be compatible with the nRF51 IoT SDK?
Anything I should be aware of beforehand...
I have an nRF51822-based device, which is a peripheral running the Soft Device s110. It has some vendor specific (custom) characteristics that are read/write. A mobile app...
Hey Nordic,
I am using the nrf51 to operate a sensor and send data wirelessly. I want to store the id of the sensor in the flash memory and I Understand that a good way to...
Hi, as I tried out the example code for PWM in SDK 9, it didn't worked for me. A closer look showed that in method app_pwm_init the method app_pwm_channel_duty_ticks_set will...
I have a peripheral (nRF51822, s110, SDK 8.1, using the device manager) which should only ever be bonded with zero or one centrals. The behaviour I'm aiming for is this: ...
Has anyone interfaced the nRF51822 to the CC3000 Wireless chip? I have started implementing the host controller functions in nRF51822. It would help me jump start if anyone...
