Hi,
I am currently making an upgrade og a nRF51422 project that has both BLE. and ANT+ Cycling Power profiles and if I run the old project on an 51822 processor I can see...
Further into development of the ReRAM file system. I noticed that in generated DTS for nRF54L15 board for the ReRAM we have:
What is the reason for providing erase-block...
Hi,
I am developing for the 54l15 using nrf connect version 2025.5.92 Last Updated 2025-05-15, 10:08:43 and it's starting to seriously frustrate me.
The nRF Connecot for...
Hi, I have two firmware images: A and B which I need to make compatible for OTA (DFU over BLE using MCUBoot - the standard process described in the devacademy course ). They...
Hello community,
I'm currently working on setting up SPI communication between two nRF5340 DK boards , but I'm running into several issues.
SDK Version 2.9.1 : I couldn...
Hello, I just try to migrate our developing project from old parent-child build to sysbuild,
But when I build the project with non-secure cpu (with TFM), I get the <err...
Hello, the CTE signal for Bluetooth AoA (Angle of Arrival) positioning is primarily transmitted over BLE advertising channels (37, 38, 39), corresponding to frequencies of...
Hi,
I'm designing a four layer flex PCB with the nRF51822-CFAC and recommended ST BAL-NRF02D3 balun and PCB trace antenna (not chip). I have a couple of questions.
...
Greetings,
Using the "central multilink" example project, how do I stop scanning if no advertisers are found? I see a case BLE_GAP_EVT_TIMEOUT in function on_ble_evt() but...
Hello
I found similar questions but no answer?
In the manual is written that I can control the parity bit in manual mode with the TXPARITY register but I can not find how...
what may be the reason for app_assert _callback error in s130,ble_central_and_peripheral that occurs from the following 2 lines
sd_softdevice_enable((uint32_t)NRF_CLOCK_LFCLKSRC_XTAL_75_PPM...
I have Rezence SDK working well with Keil uversion with wired and wireless debug without any issues on either nRF51 and nrf51822 DKs. When I port the project to Eclipse with...
Using the bootloader example code in SDK 8.1.0 for gcc, roughly how long does it take from power on to the call to bootloader_app_start()?
My device is motion activated...
Hi,
I have nrf51dk and analog EKG sensor. I know that ble_app_hrs allows to get R-R interval, but in my application i need to get also R-S and R-T intervals (or just R...
Hello,
I have combined two files spi_master and ble_app_uart into one file. Once trying to compile main.c compiles with no error but bsp.c compiles with 3 errors although...
Hi,
in S110 v 8.0.0, we can select the advertisement channels by setting the advertising parameters for sd_ble_gap_adv_start(..).
But what I want to do is to change...
Dear Nordic Team,
I am currently working on a project to develop firmware for S110 nRF51822 softdevice with the following requirements.
Read ASCII chars from a third...
i have found that
devzone.nordicsemi.com/.../
It seems impossible to connect two nrf51822,because soft device doesn't support the BLE Central role.But below said in...
I am getting an Error code on 8 on calling nrf_drv_gpiote_init() in my main() :
err_code = nrf_drv_gpiote_init();
APP_ERROR_CHECK(err_code);
Any idea what I am doing...
Links of the modules i am thinking of:
PTR7024 Module
Datasheet of the above module.
Uploader or downloader: Link
So, i am going to use this module PTR7024...
