Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
Iam using NRF8001 in my project & i don't know how to enable them & connect them through Android app basically iam using in tracking chip so any one have a idea that how to...
I am using an Arduino and NRF8001 break out board from Adafruit. I am using the UART profile (adafruit sample code) to send data between mobile phone and Arduino. However...
Hi,
I am trying to setup the nrf8001 by sending the setup commands from my microcontroller. After I send the complete setup packet (21 commands) I receive, as expected...
I'm working on integrating nrf8001 with STM32, currently trying to write my own stack.
Upon reset, I read the DeviceStartedEvent, 0x81 and it shows "0x02 0x00 0x02", which...
After a fresh install of Keil (along with Legacy patches) and the SDK, I get the following messages when I try to open the ble_app_template_s110 project:
The project...
Hi All,
I use iot_ipv6_udp_client example on nRF51 DK.
I modified it and send data in one direction only (not receiving back).
Testing has shown that the maximum packet...
Hello,
I use S130 with NUS style connections as central and device at same time. It works nice and performance is good but when i run scan, performance become very poor...
Hi,
I'm using S130 with SDK 9.0.0 and as central, I'd like to read values for more than one characteristic on a peripheral. I do so in BLE_GATTC_EVT_CHAR_DISC_RSP by firing...
Hi,everybody!
Recently,i use nrf51422 as peripheral programming s310 ant_ble_hrs example in sdk6.0 and use nrf51822 As center programming s210 hrs example in sdk6.0. I find...
Suppose I have a lot of very small characteristics (1 or 2 bytes) to send lots of notifications on. They are all updated simultaneously, though the central doesn't care about...
It seems daft, but the ble_heart_rate_template_with_battery_service example in the nRF8001 Arduino SDK does not use the nRF8001's Battery Monitor!!
Instead, it just uses...
I'm working on an application that uses the persistent storage manager to store some calibration data. I thought I had everything working well, but after higher volume testing...
Hi,
I have already developed (and almost finished) an application with SDK 8.1.1
As you now when I created the application starting from an SDK example, the project under...
Confirm all the certifications the product nRF8001 is currently holding (or in the process to be awarded).
Is the nRF8001 certified/approved to be commercially used in...
