Hi, I am currently trying to get through the NRF connect SDK fundamentals, I am on lesson 3 example 1, creating an application. The problem I am running into is that I cannot...
Background - We are laying out a new board, upgrading to the nRF54, and wanted to use p2.02 and p2.03 as serial UART lines because p1.04 and p1.05 were planned to be used...
Hello,
I face a problem which I can't understand really and where I need support.
It is strange...
In our electronics we use the nRF52840 which is enclosed in a module...
Hi there,
I have recently upgraded my software to latest ncs 3.2.0. I have noticed that my initialisation does complete but it ends up with fatal error that seems to be...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
I have set up a nrf52840 kit to upload data to nrf cloud via bluetooth but the data on the cloud is displayed as a hexadecimal number(1,2,3,4,5,6,7,8,9,A,B......) I want to...
I am not seeing a transition to BLE_ADV_EVT_SLOW. The transition I see goes from FAST to idle, without a transition to slow, from the configuration I don't expect to be in...
I am trying to implement a timer using nrf_drv_timer.h and nrf_timer.h, however, the handler never gets called.
I first create a timer, then define a timer handler and finally...
Hello everyone! I am trying to program a nrf52832 sparkfun board through a nRF52DK. I have already gone through the pin connection guide succesfully and I can flash succesfully...
Hi there,
I could program the HEX file to nRF51DK via nRFgo studio successfully and the board seems to work fine as well. And then, I try to read back the HEX file from...
I am just wondering if it is possible to use the 52840's USB interface to create an R/NDIS type interface . The intention is to maybe create a WIFI/Cellular based Network...
Hi,
I am testing ble_app_att_mtu_throughput in SDK 14.2.0 between two nrf52832 DK board. One is act as a central and other one peripheral. I am placing these two boards...
Not a question, just to tell you that in ble_gatts_attr_t Struct Reference, documentation of « uint8_t* ble_gatts_attr_t::p_value », a « @ref » Doxygen markup has been produced
I have one pca10040 board, I want to realize the data transfer between the nrf52832 and the PC by BlueTooth, I use python3.5+PyBluez. When the nrf52832 is running the "ble_app_blinky...
The following lines are copied from the SDK15.0 documentation:
<pre>
Supported boards:
- PCA10040
- PCA10040E (nRF52810 emulation on PCA10040)
- PCA10056
- PCA10059 (support...
Hi, we are using
'iOSDFULibrary' , '~> 3.0' for firmware updation process. we are getting "DFU not found" error when device is already in dfu mode at the time of update...
Hello,
I've got the light_switch example running. I would like to extend this example with the possibility to send a broadcast messages from every node, the light client...
Hi, We are facing issue with updating firmware using NordicSemiconductor/IOS-Pods-DFU-Library. we are unable to upload new firmware and getting failed operation at the time...
