nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hi Nordic,
I find somethig wrong while using GPIOTE.
I.
First I call nrf_drv_gpiote_out_init(MY_PIN, &my_config), it works fine. However, I call nrf_drv_gpiote_out_uninit...
dear sir
i had use the ble_ant_app_hrm demo to test ant+ble,but i could not find the softdevice in the folder,so i can't connect it to my mobile phone,the link address is...
Hi, I'm using Central multilink example to connect with our Custom Peripheral sensors. I'm using board PCA10040, nRF52832, SDK_14.2.0, s132. Sensors have a custom service...
For NRF51 and NRF52 antenna matching network, is there any requirements for resitors? Tolerance?
I know there are some requirement for capcitor and inductor types, how...
Hello,
Can we combine a 5-certified hardware circuit with a softdevice that is 4.2-certified? (at examble mbn52832 (module) with s332 (Softdevice))
If yes, with which...
Hello dear
I have a question about NFC on RF52832. On section 42 of datasheet, says:
"The NFCT peripheral (referred to as the 'NFC peripheral' from now on) supports communication...
hello support team,
i have seen thread and sdk14.2.0/examples/peripheral/SAADC example
pca board: PCA10040
can anyone suggest how to read battery status using handler...
Hi,
I am trying to set an nrf52840 pdk (with SDK14 and s140_nrf52840_5.0.0-2.alpha) as peripheral and central at the same time and another nrf52840 pdk just as a peripheral...
Hi,
I play with pca10040 and the light-switch example from SDK for Mesh v1.0.1. Everything works but I wonder why the advertising signals are not seen by nRF-Connect Scan...
Dear Developer Zone,
I am using nRF51822 with softdevice.
Small question about device reset : To reset the chip, do I need to do NVIC_SystemReset() or sd_nvic_SystemReset...
Hello,I'm porting a freeRTOS project to nrf51822 QFAA with 256k flash and 16k ram. I want to use s130 2.0 sd.
Previously this project was done with s110 sd and everything...
Hello All,
Please find the attached schematic , please review the same and give your valuable feed back , we are using NFC functionality in the same . earliest reply will...
Hi, We have an application with 1 central and multiple (6-7) peripherals. The peripheral is running a custom service and the central is running a custom (central) service...
