Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
I'm trying to evaluate the IAR simulator, and I'm using it w/ nRF52 samples. Besides getting errors due to the errata and system init, I'm not sure what are the use...
Hello, I was wondering if it was possible to simulate the nRF52 board using the simulator in Keil. I am trying to use it as a SPI master and it would help to be able to simulate...
In our application we use gazell. We also want to use the flash data storage which uses softdevice.
With gazell enabled, we cannot access flash.
What is the recommended...
Hardware: nRF52 DK
Example: ble_app_hrs
I have a problem with starting program using debugger. I starts debugging session and starts program using resume button, breakpoints...
I'm trying to configure SWO properly, specifically to get the output in Eclipse. The following code is used to initialise the SWO.
I have a snippet that outputs a string...
BLE is always running on Arduino Boards PROMO and PRIMO CORE
Even small example Sketches like Alarm Interrupt who doesnt use BLE functionality in the code enable the RADIO...
hi sitting and looking at the light demo example through and looking at where I do not quite understand what p_args is used to, so someone can explain that thanks: D
Hello Sir,
In last my custom nRF52832 PCB i have use 100nF capacitor mft part no: "C0402C104K4RACAUTO" but now it is nor available in digikey.
So please sir provide me...
Hi all,
Is it possible to get a softdevice which can do 2dBm output? Our device is very power critical, but we would like to have as much power as possible.
At 4 and 3dBm...
Hello, I'am working on the code of ios-nrf-beacon( github.com/.../IOS-nRF-Beacons).I found the code with Objective-C,but I'm working with swift,I want to know if there is...
What is the proper way to use the Queue Library and define a queue that can be used across multiple C files? I have the following code a my common header
NRF_QUEUE_DEF(uint8_t...
Hi all the Nordic friends and Team,
I would like to do a Batch OTA of one hundred devices right now... I'm on the NRF52 stack for my devices to be flashed. And I'm using...
I test SoftDevice V6.0.0 on nrf52832(BLENANO2) I run 1. sd_ble_gap_scan_start() 1000ms/100ms/10ms scan_window/scan_interval 2. sd_ble_gap_adv_start() 1000ms interval result...
When my mobile phone reads my characteristic, I would like the characteristic to be calculated at the same time, and not before. i.e. like a video game that does not render...
