Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Reading the migration doc at:
<SDK>/components/softdevice/s130/doc/s13x_nrf5x_2.0.0_migration_document.pdf
I see there's a new fault handler type and an implementation...
Hello all,
I need to program nRF52 via the SWD pins. I cannot use the nrfjprog or J-link or Segger etc. I have connected 3 wires to the nRF52 - SWCLK, SWDIO and GND.
...
Hello to all
I'm working in an application that needs to be completely power optimized. In this program the device works as a scanner that if it finds an specific device...
Hi, I am wondering about the pre-made PCB's available on ebay, with a nRF24L01+. At a cost of $1, and with various forum stories over the Internet referencing issues such...
I am using NRF51422 S130. I have a master SPI configuration set up, and not using Nordic spi drivers provided in the examples. I think my configuration is correct.
1- I...
Hi,
We started out developing an application using the SoftDevice 1.0.0-3 (from SDK 0.9.2). We now need to upgrade to SoftDevice 4.0.2 (included in SDK 13.0.0).
We already...
Hello, I have some ideas to do for IoT and bluetooth. Already did some tests with MQTT raspberry pi and ESPs SoCs. Then I started to dive into bluetooth world and I found...
Hello,
I'm working with SDK 11 on nRF52832.
I want to get the IRK from a connection event. I need to identify the connected device.
My following code :
static...
I'm developing a multi-peripheral application on the nRF52832 that started from the SDK v13.0.0 experimental_ble_app_multiperipheral_pca10040_s132 example application (running...
I have two nRF52840-pdk's and two laptops. I was thinking to send test strings using the following Basic setup:
laptop1 - usb1 - pdk1 ....(coded PHY transmission)....pdk2...
I was able to write the code and put it to work on AN5 pin , and I found out that whenever I approach to the DK board he see it as a touch.
I connected to the pin a 10cm...
Hello all,
I am trying to make use of some Adafruit libraries for some sensors in my nrF52pca10040, the libraries are these two Adafruit_BME280.cpp , Adafruit_BME280.h...
Hello
In a schematic I saw the "SWO" connection appear on the Programming/Debug connector beside SWDIO and SWDCLK.
What's it for?
Of course it means "Single Wire...
I want to increase ble_app_uart_pca10040 app sample rate.
I have my own board with microcontroller and use nrf52832 as uart to ble.
I made pack length to 20bytes, I have...
