I was doing development on the development kit and I noticed that when flashing the device there is application core and modem core firmware that is flashed
I'm trying to...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
hi sit and test bluetooth mesh and i do not quite understand how the client knows that the server is off or on and there is a way to find out if a server is on or off
Hello,
I would like to use nRF52840 in order to make some BLE5.0 mesh products. When I open the nrF5 for mesh, I can see only examples for nRF52832.
Do you know if these...
hello, i am trying to implement external RTC in my application. i am using the SDK 14.2.0 and softdevice s132 .n also for external RTC using the M41T62 with nrf52832DK. so...
Maybe there's a secret I'm missing but this looks like a development / debug flag that got left in.
I'm porting an app from SDK11 to SDK15, when I call app_button_init(...
Hello
There seems to be no makefile in this example to use with armgcc compiler(why?) so Im trying to port it using the makefile from the ble_app_att_mtu_throughput example...
How to write driver for ADC by accessing direct registers of nRF52840 ?
I don't wanna use SDK APIs.
I wanna read LDR value connected to A0 (PO.3) pin in continous mode...
Dear all,
I'm trying to change the advertised device name during advertising depending on some variables.
I'm observing with nRF Connect and Lightblue, both running on...
Hi,
I have followed the steps for the 2 demos for nRF52840 DK, the Heart Rate and the Proximity demo. In both cases, when disconnected from the android device, the evaluation...
Heey everyone,
I'm currently working on a wireless application and we would like to have a range of atleast 300 meter. Yesterday I was testing the range between 2 SDK...
I work with Kenkou GmbH in Berlin. We are looking for Firmware Developers and Engineers with Mid - Senior experience to support our project. We are hoping to extend the visibility...
Hi All, Nordic,
In my application, I don't always need BLE connectivity, so I was hoping to disable the S132 softdevice when not needed. However when I do this FreeRTOS...
Hi,
I am working on a project with BLE and TWI module. With some help, I manage to set a TWI communication ( https://devzone.nordicsemi.com/f/nordic-q-a/29371/twi-issue...
Every once in a while I will get a failure that results in the app_error_fault_hanlder() being called and the following info:
ID = 1
PC = 0x14550
error_code = 0x495...
Hi, I use ble sniffer 2.0 beta with nrf51 (pca_10031_51296aa.hex). Is there a sniffer api documentation with description of the UART protocol (as with sniffer 1.0.1)?
