I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
I am using nRF Cloud to update firmware on nRF9160 based products in the field. They are connected via LTE Cat-M on Telstra in Australia. The problem is that the download...
I need help with this issue. I'm updating the code from SDK 2.4.2 to SDK 2.9.2. I had change the device tree to HWM2 and I'm using sysbuild.
The build log is showing this...
SDK: 3.0, nRF54L15
I have modified the clusters using ZAP tool (west zap-gui). When I tried to built, I get the below error:
1. I used Matter door lock sample and the...
Hello, I'm developing on an application which requires to catch high speed, variable size and bursty (~0.5 Mbit/s) data from a sensor connected to a nRF9161DK trough a UART...
If I try to compile any of the WIFI examples for the Thingy91x I get a RAM overflow error. The only exception to this is the WIFI scanning example. If I build these for any...
Hi,
I got the nRF52840 preview development kit and I am trying to follow the quick start guide here:
link text
It works fine for me up to step 7, where I am supposed...
Hi
I have gotten a Nordic PCA10040 hooked up to a Sparkfun nRF52832 as described near the bottom of the page here: learn.sparkfun.com/.../nrf52832-breakout-board-hookup...
hello,I'm having a problem with the ANT application,I have two pieces of the PCA10040 board as a ANT connectivity board for a ANT application board.According to the instructions...
Hi,
what is the default tx_power value in new v13.0.0 SDK in the ble_app_att_mtu_throughput example?
I can't find the use of the sd_ble_gap_tx_power_set() function which...
Hi,
After configuring the nRF51422 as a SPIS slave 0, we get the following error when trying to create the slave instance:
static const nrf_drv_spis_t spis = NRF_DRV_SPIS_INSTANCE...
Do you have any ready made example where beacon and NRF52 DK are communicating will each other.
Our idea is that beacon sends data to the NRF52 DK and NRF52 DK sends the...
Sorry if this is obvious but I cannot find the units of nrf_esb_config_t::retransmit_delay
in the SDK documentation, it just says: "The delay between each retransmission...
Hej,
I'm working with the nRF24L01+ and the ATmega328p programmed in c. The goal is to have both TX and RX mode in the same device, mainly work as RX but in certain conditions...
Dear sirs, I've had a difficult time establishing communication between my nRF24L01+ board and the SPI bus on my Arduino Uno R3 microcontroller. Could you please provide me...
Hi all,
I am thinking of using a GPIO pin's "SENSE LOW" to wake up my device from SYSTEM OFF mode.
In order to avoid the device keeps waking up in case the pin stays low...
I am using an nrf51822 DK with a (so far) very simple code along:
main()
{
//... init I/O
run();
}
Inside run:
run()
{
uint32_t retval = NRF_SUCCESS;
...
Hey,
I recently got the nrf52 DK and tried to make use of the app_button library to have easy to use debouncing.
As far as I understood the library, the event should be...
Hi,
i have a problem withr the example "BLE ATT_MTU Throughput Example".
I flashed the soft devive with nRFgo Studios. Now I want to flash the example, but i got following...
