Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0).
I understand that softdevice uses MWU from this document
As per the Errata...
Hello,
I'm a newbie here.
I have a BL652-SA module from Liard Connectivity. It has a nrf52832 with a 32 MHz crystal on board but no 32,768 kHz crystal, so I have to use...
To the kind attention of Nordic support team,
I have been successfully using all gzll routines like in https://devzone.nordicsemi.com/f/nordic-q-a/57839/how-to-prove-to...
Hello-
I am developing my first project with the nRF9160. It is on a custom board. I am planning on using Segger studio with the Segger JLink programmer with the 10-Pin...
I am using nRF52832_xxaa DK and compiling ble_app_eddystone example. I am getting the following error
JLink info: ------------ DLL: V6.54c, compiled Nov 7 2019 17:01:02...
I wrote a simple application which updates a 16 bit characteristic as fast as possible (after initializing everything). Similar to the following:
The function called checks...
Hi,
example : nRF5_SDK_15.0.0_a53641a\examples\peripheral\twi_sensor
I am using the HTU21D sensor. I was download the twi_scanner example to scan the HTU21D sensor's slave...
I am having a problem talking to a MMA8653FC 3-axis Accelerometer from NXP.
I never see the clock signal generated.
I am using the nRF52 lib, communicating to a nRF5280...
I am converting the the Project ‘usbd_ble_uart_pca10056_s140’ to pca10059, to download it in the nrf52840 dongle. I followed the steps in the nRF52840 Dongle Programming Tutorial...
Hi,
I have some problems when I tried to compile pc-ble-drivers (C) .
1. When I tried to execute ./bootstrap-vcpkg.bat after I follow the steps:
$ git clone github.com...
I’m studying the NRF9160-DK board - I installed the Basis SIM card and followed the instructions : www.nordicsemi.com/.../GetStarted
I launched the Link Monitor program...
Hello,
My thingy:91 is publishing its messages to nrfcloud (=to the corresponding AWS mqttEndPoint and topics/ I suppose AWS IoT Core).
Now I want to get/process these...
In the example / serial in SES I see the softdevice is loaded as an "additional load file"
$(SDK_ROOT:../../../nRF5_SDK_16.0.0_98a08e2)/components/softdevice/s140/hex/s140_nrf52_7...
I am quite new to the nrf9160. Trying to run the gps example https://github.com/ExploratoryEngineering/nrf9160-gps . But everytime I get an error Failed to start GPS. I am...
