Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
Hello everyone,
We are 4 students, who are developing a BLE mesh network to send data from a CANNBUS-simulator to a desktop. We have chosen to use the nrf52840 chip to set...
Hello,
I am using nrf52832 with SDK 16, I want to change advertising packet flags from BLE_GAP_ADV_FLAGS_LE_ONLY_LIMITED_DISC_MODE(0x05) to 0x04 during run time how can...
Hi, Im developing an ac dimmer with zero crossing on mesh, but it flickers at low dimming levels, I even used the scheduler for the ble stack but it didnt help, what would...
hi, i am using nrf 52840 dongle , is there any support of AT commands to communicate with dongle .i want to communicate without using ui only by sending commands. if not any...
Hey Nordic Team!
My requirement:-
Sensor data----------------------------->nrf52832------------------------------>Raspberry pi 3 (via blue tooth)
Is it possible...
We are working on external RTC MCP7940(i2c) interfaced with nrf52840. Please check if drivers of the same for nrf52/51 are available or any implementation of CLOCK using MCP7940...
Hi,
I tried to add 3 characteristics and 1 gatt service to my NRF52810 using with development board with 10040e (I am using gcc compiler). Then I got a error which is saying...
we are considering using .005" thick stainless steel to provide better bridging effect across the opening on the board for the battery. This will provide more strength to...
Hi
I am trying to use an antenna switching board for AoA direction finding. I know that the RADIO controls 8 PSEL.DFEGPIO pins to control switching antenna.
1. Could...
Hi,
We want to use the NRF52810 without radio and we don't want to put the external oscillator to reduce the PCB size
I would like to know if necessary to have the external...
Hi,
Some time i could not put break points inside main for sample projects provided for nRF91, i tried clean build, erasing the flash 'nrfjprog -e' and evn enable the configuration...
We would like to use a Dongle based on the nRF52840 as a BLE Central communication via NUS to our product. The example in the nRF Connect Desktop does just wat we need on...
Hi，
I want to use none secure example on nrf5340.
The code can't run with ns config(uart didn't log anything),But it works fine with normal config.
How can I sovle this...
Hi, devzone.
Since I was recommended last time, I started reading the BLE tutorial .
I first saw a this tutorial .
Even if nrF52-ble-tutorial-advertising is placed in...
Hi,
I have a custom nRF52840 board. I mistakenly tried flashing the custom nRF52840 board with STM32 firmware. From that moment on, I can't flash board. When connected...
