I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hello Nordic Team! I'm experiencing unusual issues with GPIO pins on an nRF54L15 custom board. Specifically, P0.02 and P1.03 are not behaving as expected. Button Issues (P0...
Hello,
I am developping an application based on PAwR (Periodic Advertsing with response) in coded PHY (S8) extended advertising on SDK 2.7.0.
costum chip nrf52840 (on...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
Hi, the Nordic team
I am a novice, I now want to use the serial port and my radar module to communicate, how do I achieve this function?
I use the sdk is 2.9.1
Best...
Hi all,
we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hi everyone,
We're reading BAT level by reading data from ADC pin and the setup diagram is shown below.
We tested our device at hospital, and we observed significant...
I am trying to populate a nrf_twi_mngr_transfer_t at runtime depending on chunks of an input file that I'm pushing to i2c.
nrf_twi_mngr_transfer_t const write_cfg_transfers...
We are currently working on a project based on Enhanced ShockBurst (ESB) and would like to use Front-End Module (FEM) support with the nRF21540.
In your Enhanced ShockBurst...
Morning, I was trying to access https://academy.nordicsemi.com/ but the browser responded with an error `Domain configuration pending` and showed `Kinsta` node is down. Any...
Hi Support Team
We follow the guidance of the following link to program firmware to external SPI Flash of nRF54L15,but it failed.
https://docs.nordicsemi.com/bundle/nrfutil...
Hi,
I am desperate with creating my own board. I followed the example of nrf54l15dk, but I absolutely do not understand why I cannot build - not even assembling Zephyr....
Hello,
I am working on custom hardware that is based on the nRF7002 DK. The following parts are presently listed as either EOL or NRND in distribution. L6, L8: Taiyo Yuden...
I am trying to connect some I2C sensors to the the nrf9151dk and I cannot figure it out. Where do I physically plug the sensor into the board and what configuration setting...
Hello,
Hopefully this will be a quick(ish) one since I think I found the answer, but just need confirmation.
To preface (My setup):
nRF9151DK
Modem firmware: mfw_nrf91x1_2...
