Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello,
I am trying to run the BLE Thread Dynamic Template example on a nRF52840 dongle. I'm using Segger Embedded Studio to generate an hex file. I flash the hex file to...
Hello,
During testing we found that whenever in system off mode, the CPU wakes from VBUS rising. As expected. We then do a vibration to notify the user the USB cable was...
When integrating nRF Mesh SDK 4.1 with nRF SDK 16 I got an error in runtime.
The call sequence:
mesh_init() -> mesh_stack_init() -> nrf_mesh_init() -> mesh_config_init...
Hi all,
I have really strange behavior with Sesgger SES. I'm working on Linux Kubuntu lastest version.
Segger version is :
SEGGER Embedded Studio for ARM
Release 4...
I am trying to use C++ with an nRF5 board, but I'm running into issues with the MDK, IAR (v8.40.2), and C++. When I try to include "nrfx_gpiote.h" in a .cpp file, I get the...
Hi,
I have a basic setup consisting of a time-slotted transmitter and receiver so that I can experiment with the raw coded and uncoded modes, exploring all the NRF_RADIO...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hi, I want to create a mesh network with two nrf52840 dongles. To programming them I used the light-switch example from SDK Mesh v4.0.0 following the steps in this tutorial...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
When I connect to nRF52810 with RTT viewer and then unplug J-Link probe from the device without properly closing the connection in RTT viewer, the current consumption in deep...
Hi everyone,
I want to measure the total execution time of saadc_sample() & saadc_callback() functions. I am using the application timer and I have inserted the app_timer_cnt_get...
Hi everybody, I am a beginner and I need your advice to start to modify the example of Radio Receiver/Transmitter. Ultimately my goal is to measure the time between the reception...
Error message from KEIL CMSIS D/L :
Update available for ARM::CMSIS (installed: 5.6.0, available: 5.7.0) Update available for ARM::CMSIS-Driver (installed: 2.5.0, available...
I have developed an bootloader operating with external flash for image storage. For the use case it is not acceptable to put the device into an inoperable (no-application...
