Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi Devzone!
The development is in the final stage and is now testing by connecting the dc adapter or battery, not by connecting the pc cable and the debugger. However...
To get the reason for the restart, I called the sd_power_reset_reason_get () function after the ble_stack_init () function in main, but there was a problem. The return value...
Hi,
I'm developing a project which use softdevice and some peripherals together. I want to use serial communication with uart. But i couldn't initialize the app_uart module...
Hi there, Im successfully sending 1.1mB om data from Android Samsung S9 or iPhone 11 Pro. My problem is the low throughput i achieve, its about 6.1kB/s on iPhone and about...
Hi
I have a few questions as a newbee on Nordi products:
Can nRF9160 be used as modem via UART in the same way as i.e. Simcom's ?
Is it possible to run code on the...
nrf_log_push is declared as
I think the const in the parameter should be before the pointer not after it? const-qualifying a parameter (as opposed to the chars pointed...
I am developing a device based on nrf52840, this is peripheral. But I want to change the code so that I can only connect to my device using my application (in other cases...
Hello,
As I am using max30003 ECG with nrf52840 Using NRFX_SPIM example code( SDK15.2-PCA100056 ), I have developed drivers and I am able to read device id through my driver...
We had been using an AT&T M1-enabled SIM in one of our development units successfully for quite some time. After we upgraded that node to MFW v1.1.0, it is no longer able...
I have a custom board based around the nRF9160. I am trying to use the LTE Link Monitor to test the Modem but and having problems.
I am able to connect to my board OK, please...
Hi Nordic teams,
I'm trying to integrate the DFU function into light_switch example this days. At the beginning, I used the dfu example to update my evaluation board, and...
Hi,
Good day!
Statement of problem: In our application, we are using nrf52832 SoC to control critical components (heater). So I was suggested to use a watchdog timer to...
Hi,
Im trying " https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master/samples/nrf9160/gps/src/main.c " gsp example to check supl(AGPS) to integrate into my application...
Hi,
In-app when you scan for device and after it is found you press the connect and then the notification/permission to pair pops out. Our app developers are saying that...
