Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi teams,
I have build custom board connected to ethernet via ENC28J60 ethernet controller.
It uses SPI communication with ENC28J60, but some strange behaviour during...
hello
i am using nrf52832 with pwm driver (working with ble and s132 if it metters)
i need to control 4 different motors speed via pwm, since there can be only 3 instances...
Hi
I have implemented a scannable advertising on nRF51822, s130, SDK12,
I can see it's working by reading the scannable information on nRC Connect, however,
on the sniffer...
Hallo,
I have a question reading the datasheet. It states:
" If a regulator is only to be used in LDO mode, the inductor for this regulator is not needed. "
I want to...
Hello,
i'm trying to understand how nrf52 and softdevice work to use it in the future, i'm working on STM32 and i have my own RTOS, i try to appropriate the platform by...
I received my NRF52840 dongles and downloaded SDK 16.0.0 and SES 4.52c. I found some old documentation that said how to convert ble_app_blinky to the dongle but then exploring...
Hi,
I have nRF52840 Dongle(PCA10059), I try to develop on the nRF Connect Desktop. But this dongle can't update firmware on the nRF connect desktop.
My operation below...
I’m using the latest version of the modem 1.2.0 and sdk v1.2.0
For the most part AWS FOTA seems to be functioning.
However it will start the FOTA job and hang and fail...
Hi everyone,
I need to set up a timer using the RTC. The default function that converts ms to ticks APP_TIMER_TICKS() accepts only milliseconds. So, I wrote my own conversion...
I want to interface Client Sensor over UART in light_switch_client code. Can you please give me the idea,how to do it.
I am using Mesh_V4.0 and SDK 16.0
Hi, teams.
I am trying to implement DFU functionality on mesh node devices.
Currently, I am using Mesh SDK 4.1.0 and have read DFU-related documents, but still something...
Hello -
We are working with a custom board that is similar to the SparkFun Pro nRF52840 Mini . We are using the nRF52840 SDK version 16.0.0 and SoftDevice 6.1.1. Our board...
Hi everyone.
I am working on the ble_app_bps_pca10056_s140 example. I want to confirm that a BLE event is received when the APP_ADV_DURATION has been expired.
After searching...
Hi,
I noted that the CW generated in the %XRFTEST TX test seems to be offset from the requested frequency. Specifically, issuing the command
AT%XRFTEST=1,1,20,8500,-50...
