Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
nRF9160 DK (PCA10090) is continuously rebooting.
I have flashed following Images and tested, but same issue (rebooting continuously) observed.
1. Pre-compiled...
Hi,
I try to build and programm Thing:91 with segger embedded Studio and need the file app_signed.hex to Flash the Firmware in Thing:91 without a external debug probe. After...
Hello
I have a 3 custom PCBs with nRF52832 (1 central and 2 peripherals) and 1 nRF51 dongle (peripheral) arrangement where the two peripheral nRF52832 boards (custom PCBs...
I have just switched from SDK version 1.0.0 to SDK 1.1.0 and I am using the MQTT FOTA example
I had the example project working when I was using v1.0.0 of the SDK
I...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) Do we need to call fds_record_close...
Hello everyone!
I tried to write data directly into flash using flash manager from nrf SDK, but according to docs it does not work with ble mesh.
But mesh flash manager...
Hi to everybody,
there's a way to force a Zigbee router device to send Announcement Command at certain time interval also if it's already joined to a network?
I saw that...
There are two capacitors (C18, C27) that are labeled as N.C./Not mounted but there is no description for their existence at all. Do I need to place those pads?
i have a some XX byte of custom advertising data and we are following the SIG specifications , i want to update my advertisement data which is not part of the structure "ble_advdata_t...
Using LFCLK, enabling and running the WDT causes the nRF52840 to hang until the watchdog reset when calling nrf_drv_clock_lfclk_release . This is with SDK v15.2.0 Steps to...
Hi I'm using nRF52 DK to program a BM832 module where I want to run some code to manage FLASH memory. I make run examples on the DK but on BM832 module can't be possible because...
Hello Nordic Community!
I have seen previous posts mentioning that the DFU example was not working with SDK 15.3 ( Getting started blog ). But in my case I was able to...
Hi all,
I am working on a new project and I need to communicate to a sensor using I2C, then save the data on a flash (files visible on windows as mass storage via USB) and...
Hi,
I am developing an application where the device should support both central and peripheral roles at the same time. My devices are connecting to a mobile phone. All the...
