Hey Team,
I'm trying to flash the audio application on our custom PCB, this PCB follows the interfaces of the nrf5340 audio dk. Previously on lower SDK versions (2.7-2.9...
Hi Nordic team,
This is a follow-up to my previous question here:
Can nRF52833 perform PAwR while also syncing to another PAwR device?
We are now extending our design...
Hi,
I'm trying to build nmea parser, so I have a functionc hecking all nmea sentences and trying to get double value, but I always go bad double value. For example here...
Hi
I am trying to setup and test the OpenThread CSL feature on nrf52840DK with OpenThread daemon and RCP mode nrf52840DK.
I found there is a way to build the Daemon for...
Hi,
With several nrf52840 based prototypes, I had serious problems. I could see them die after flasing them a few times. And this was not just one dying, it was all of them...
Is a common ground required when measuring current in current meter way?
Can externally supplied voltage exceed 5V? Will this cause inaccurate test results?
I'm working with nRF5340 and nRF Connect SDK 2.9.0, using sysbuild and Partition Manager for my project. I want to enable Zephyr's coredump feature and store dumps in internal...
Hi Team,
I would like to know what does the system do after I call system off function as per below:
I have check through the oscilloscope to check how's the system...
Hi Team,
I am in the UK and trying to get an evaluation sim from Vodafone for NB-IoT. However they have set a limit of 2 IP addresses and hence I need the IP address of...
I'm developing bluetooth logging software on the nRF51 DK using SDK 12.3.0. We had been developing for some time in mbed, but were advised to switch over to Keil using the...
Hi,
I'm working on sending reliable message from server to client, the models are modified from RSSI model.
When I tring to send messages to client it will keep sending...
I've been trying to store an array (SDK16,S332)
uint8_t my_data[]={0x00,0x01,0x02,0x03,0x04,0x05,0x06,.........0x23}
using fstorage I wrote an update function :
I hardcoded...
To the kind attention of Nordic support team,
I'm trying to do things like in https://devzone.nordicsemi.com/f/nordic-q-a/39630/windows-command-line-dfu-over-ble-with-pca10059...
Hi,
I have a project which was originally written using SDK12, and have updated it to SDK16, I am sorry I know this question seems to have been asked in many different ways...
Dear,
Like I said in the title, I did use the NFC of my PCA10056 with my phone, it works, I also can read some information from nRF52840 by NFC. Right now, I programmed...
Hi Devzone:
I am working on nRF52840 with latest SDK.
I have 1 differential pair and 1 single ended pin I want to sample, single ended samples at every 40ms while differential...
I was trying to connect my cellphone tu the ublox modulo for sends at commands from my cell, in the main program of the micro I've the next lines for turn on the ublox module...
i have a nrf52840 dk
i need to connect the flex sensor to the board and know the resistance value while bending
how to do it?
and what code should i dump
Hi there,
I have developed the custom board with nrf52832 Soc and programmed blink code, it works fine.Now i uploaded the ble DFU template example and updated firmware...
I can't install the tool chain.
Looks like I have to install something called chocolatey?
I can't install chocolatey. I tried the chocolatey website for help and was baffelled...
Hi, I am trying to debug the blinky project with Eclipse, openocd and st-link. No softdevice. This is the output I am using.
I am finally able to see the leds blinking in...
I am studying to use the nRF2460 or wireless digital audio streaming where one Tx broadcasts and several receivers listen and follow. I have the following questions: Can an...
