My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hi,
I am using the nrf54l15 on a custom board in our current project and want to use it with DFU over BLE FOTA as well as TF-M.
I can compile the project just fine before...
Dear Nordic Semiconductor Team, I hope this message finds you well. I am currently developing a project called Nuntius Core, which involves controlling bait boats (carp fishing...
Hello,
I am currently working with the nRF5340DK and the W5500 shield. Both work perfectly when using the dhcpv4_client application. However, when I attempt to use the recv...
Hi Support Team
We follow the guidance of the following link to program firmware to external SPI Flash of nRF54L15,but it failed.
https://docs.nordicsemi.com/bundle/nrfutil...
I am trying to light-switch test different features in my app to see if I can save some memory, and I found that the examples\peripheral\cli example won't compile if I turn...
The bluetooth of android APP is easy to disconnect (we make smart door lock products); The product is delivered to the customer. It is easy to disconnect and not connect with...
Hello,
I learnt about some resource pre-allocation in the datasheet, e.g. ppi, or API documentation, e.g. app_timer rtc1. I see the SDK drivers are trying to take care some...
SDK16, S112, 52810. I have DCDC set up and external 32.768 crystal oscillator on my board.
Here is my code part:
main()
nrf_power_dcdcen_set(true); nrf_delay_ms(100...
Dear ,
Follow the previous ticket, https://devzone.nordicsemi.com/f/nordic-q-a/59034/agps_thingy91
I am trying to use asset_tracker : https://github.com/NordicPlayground...
I am writing an application on a BLE chip that will transmit high volumes of data to an Android phone (520,000 bytes / second signal).
According to some tests I've seen...
my board uses 51822. I am using 52DK to debug it. I have plugged my board with 52DK as following:
RX -> p0.08
TX -> p0.06
My question is, when I init UART in code...
Device: nrf9160 (dk and custom board)
sample application : MQTT simple
segger studio (nordic version): V4.42a
There are 2 main issues:
1) in the main.c file, Segger...
Last time I used it, it worked fine, it's been sitting in a drawer for some time since then.
When I tried to use it now, i get this error - even though I can read the...
Hi team Nordic,
Looking in the nrf53 datasheet, it seems like the PDM clocks are the same (peripheral) as the nrf52, is this correct?
You usually wanna run the newer high...
Hello,
I am using an nRF52840 on a custom board, and I want to add the workaround for Errata [87] Unexpected wake from System ON Idle when using FPU . However, the the...
Hi,
I´m trying to flash a custom board with nrf52833 chip with the nrf82833 DK.
How can i make sure, that tha DK board will program the custom board? Currently it...
Why isn't this working?
The MPU_RESET_PIN is set to : NRF_GPIO_PIN_MAP( 0 , 20 )
I can not seem to be able to alter the state of the PIN. Whenever I read the PIN its...
Hello all!
I have a timer that sometimes gets started inside the IRQ of the ESB and sometimes needs to be restarted inside its own IRQ
I'm running it in a "one shot...
