Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hello,
I'm currently levelling up a project based on an older SDK which involved SoftDevice v5 (S132) to SoftDevice v7 (S140).
As far as I understand S132 and S140 are...
Hello,
following the peripheral/saadc sample, which shows the periodic reading... could you please share the essential and minimal config for the One-Shot measurement? ...
I want to integrate the XMOS (XUF216-512-tq128) with nRF52840 where the nRF can be used to perform the field updates for the XMOS. Is there an application note or an example...
hello,
i am using nrf52832 device with soft device of S132.
i am trying to connect 2 different applications on the same smartphone to the peripheral device. currently...
I have two NRF52840 dev kits that are running what are essentially the spi master and spi slave examples. They both work and I've altered them slightly. I'm just kind of confused...
Hi,
I've been trying to combine the spi_slave and USB_CDC_ADM examples so that I can pipe data from a spi_master all the way to my host machine. In my cobbled together...
Hello ,
Is there any development KIT available for the Evaluation of Direction FInding - AoA and AoD ? Any code examples for the same?
If not what is the time line?
...
Good day,
I would like to switch between two states once I receive a trigger. state1 <---trigger--->state2.
State1 = Beacon/custom manufacturing data - Beacon Example...
Hi,
In my application after some timeout i am trying to stop BLE advertisement.
for this i am checking current connection state,If it is connected or disconnected.
if...
I'm using the TWI_MNGR to schedule a transfer. I have copied the nrf_twi_mngr_perform() function to a function called nrf_twi_mngr_schedule() which does everything except...
Hi team,
I am working with the nRF5340 PDK v0.8.0 and I am trying to request the additional voltage for the VREGRADIO to support the additional 3 dB TX power on the RADIO...
i have a project with Nrf24, i'm using NRF24L01 + PA LNA 2.4Ghz with athena, to get 1000m -2000m range.
But i saw on nordic website that nrf24 not for new design, we have...
I have seen a few references to SoftDevice in the 6.x series not being able to transmit at 500kbps in these forums, but I can't find anything in the docs to reference. Can...
Hi, I am using nrf52832 dev-kit. I use P0.23 or P0.24 as an input pin. I am trying use this pin to read data from other device. When I use this pin like button, it can detect...
Hello,
I would like to get some input on general framework options for development.
I am starting by strictly following the SDK framework, trying to use its drivers, translations...
