Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Hi all,
I have an nRF52 acting as Central, and it will act as beacon just when it, for example, reach a temperature above a certain point. After some time, e.g 10 calls...
Using SDK15.3.
Using the logging in deferred mode with RTT viewer.
Getting the errors below from the macro expansions but I can't identify what is missing.
Went through...
Hi,
I made a temperature logging device using nRF52832 (SDK 12.3.0). The temperature sensor is read over I2C every 5 minutes and data is sent over radio communication. There...
Hi,
I have setup the SW project to run run FreeRTOS with BLE stack initialized and nus service started without doing any further BLE use after init in runtime. Sometime...
Hello,
I am using an Adxl362 accelerometer on nrf9160 dk board.
I followed the tutorial a to add the overlay file and even configure the pins i want to use by flashing...
To the kind attention of Nordic support team,
It seems gazell is a very good candidate to be used in tipical working environments, where a bunch (<= 5 devices for example...
Hi,
I am new to Nordic. I bought an NRF52 DK and a Fanstel EV-BT832 development board. As you can see in the picture, both boards are connected to the computer via USB....
Hi,
I had some of your example projects which were being evaluated within Keil and SEGGER and now have an issue with Keil after updating to the PRO license.
I now get...
Hi,
For a peripheral reset, I was recommended to use the code below.
I was just wondering about what the middle line does. Is this a kind of delay to make the reset...
I am trying to start the mesh alongside GATT profiles. I am getting error NRF_ERROR_NO_MEM when calling sd_ble_gap_adv_set_configure in mesh_adv_data_set, which is called...
Hello,
I get the following output when I try to debug the Zephyr's button sample with SEGGER Embedded Studio:
Preparing target for download Executing Reset script TargetInterface...
For the nRF52833:
The product specification is contradictory on the 2 UARTs available. Would you please clarify?
UART0 is this a legacy UART only or does it have Easy...
Our customer has requested access to any test suites the BLE IC vendor can provide which can be used to provide objective evidence of testing & specific test cases.
We started...
I use sdk 15.3.0 / nrf52832 / SD_132.
How to use the prescaler of a timer for an event every 24 hours ?
An example will be very explicit.
Best regards, Jiemde
Hi,
I am trying to evaluate the nrf52840. I am following the instruction to instrument the FreeRTOS from the Nordic SDK15.3. I managed to follow most of the instructions...
