I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hi,
I am completely new to this technology,I need to interface BME 680[humidity,pressure,gas,temp sensor] with Nordic nRF52840 - how it is possible,i want know the hardware...
Hi,
I am using nRF52832 DK, with Segger Embedded Studio as IDE. I am using ble_app_uart example. I have used an encryption algorithm. The encryption algorithm is called...
Hi,
Does the SPIS generate interrupt for every byte of data receive ?
What kind of interrupt of event that SPIS will generate for data received ?
Please advise
Hi,
I need to assign Rising edge and Falling edge event in a single pin.
I try to assign both Rising Edge and Falling Edge event into APP_EVENT_PIN.
There is a error...
Dear all,
I have noticed that NRF_LOG_FLUSH() function is used in many examples after each nrf_log print function. In some cases though, the program freezes when I try my...
HI!
nRF52832, SDK13
I need to know what happen with setted output RF power when peripherial devie connect to central device.
For example, if output RF power setted to...
Hi,
I am completely new to this technology. I am currently programming a custom board equipped with an nRF52832 based on the ble_app_uart example in the SDK 15.2 and is...
Hi!
24 days have passed since I was promised an update (which I hope will mean a solution), but nothing...
Also, there is no updated Getting Started Assistant and the...
Hi,
We are planning to use an Automotive Grade Bluetooth SoC in one of our new designs.
Some controllers in the nRF51 family seems to be Automotive Grade, but we also...
I tested with Light Switch Example in nrf5_SDK_for_Mesh_v3 version, I have set Transittion time to 160 second and Delay to 0, problem occur is the device Cann't countdown...
Hi,
I am using an nrf52840 MCU, Nordic SDK 16.0.0 and IAR Workbench for ARM v8.40.1.
The MCU has the following configuration:
- MBR installed
- DFU secure bootloader...
Hello everyone,
I faced with bus fault after running beacon example from mesh_sdk. It occurred after calling mesh_provisionee_prov_start().
Unfortunately, I didn't found...
Greetings...
Provisioning w/ Android tool only works when board is connected to debugger.
Provisioning failed to even find the devices when scanning after disconnected...
When enabling 3 instances of SPIM (1,2,3) on NRF52840 the application doesn't start at all.
Weirdly however, the application works fine when SPI3 takes SPIM3 and the rest...
