I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hi, how to link nRF51 IC rev. (1, 2, 3) in NRF51 Series Compatibility matrix ( https://infocenter.nordicsemi.com/topic/comp_matrix_nrf51/COMP/nrf51/nRF51422_nRF51822_ic_rev_sdk_sd_comp_matrix...
Hi everyone,
I am working with SDK 15.2 and Mesh 3.1 with NRF52832 DK.
I am testing the ble app uart coexist example provided by nordic.
I followed the steps provided...
Hi,
I have a problem with Secure DFU Bootloader available from SDK 12.1 on nRF51822_xxAA SoC. I use example in SDK 12.1 and when i download it to nRF51822_xxAA it isn't...
Hello,
I am having problems with a custom NRF52840 Board. My program hands at the ble_stack_init function.
I have encoutered this problem in the past so I have tried the...
Hi.
I try to implement LESC using nRF52810.
But I use a Static passkey because my device doesn't have a keyboard or display.
One question is, is LESC more secure than...
Hi,
I try to use QSPI to communicate with Gigadevice NAND flash http://www.datasheet-pdf.com/Search-Datasheet-PDF/GD5F1GQ4 . There's no DK, the custom board was produced...
Hi everyone,
there is a post dated 11 months ago from now in which Nordic tells that -40dBm Tx power configuration is feasible but not recommended ( Case ID: 230320 ). ...
I merged the code from the SDK examples "usbd_audio" and "usbd_cdc_acm" and have ensured that each has their own INTERFACE and ENDPOINTS. I am able to download to the development...
Hi,
I am developing with nRF52832, SDK 15.3
I have an issue with sending data over NUS service. When I flash the code to nRF, it starts advertising, but when I connect...
Dear sir,
The twi sensor code in SDK14 is getting stuck at NRF_BREAKPOINT_COND. Also, on the uart terminal it is showing FATAL ERROR . Please help me out of this.I am using...
Hi
I want to set up a network of about 4 groups of BLE light modules(using the experimental dimming example). Each group comprises of 5 to 7 light modules.
Currently the...
Hello, my code was working just find then I tried to add the user description value to my characteristic. In the example below I had set it to "Test" for now. Once I did this...
hi
i am programing BLE blinky app blinky which advertise. yes, the same code i am trying on custom board works on nrf52DK which has LFRC crystal activated as mentioned on...
I am trying to add my nrfcloud certificate to my nrf9160-DK but the AT commands do not work due to a timeout.
My procedure is as follows:
1) Downloaded the "nrf9160dk_fw_2020...
Hello Nordic team,
I'm getting started with BLE, using the 52832 SDK16 HID mouse example. In the example, clicking the button only moves 5 pixels. How can I move the cursor...
