How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Now I'm developping a USB MSC project, the Nand flash size is 4GB, I don't know how to set USB capaticy size.
I change the setting in nrf_serial_flash_params.c:
static...
Use the media control's volume up / down keys to control the camera shooting of your Android camera. How to achieve continuous shooting?
How to achieve the function of camera...
HI
I'm writing a programm the using a nus as its service, because nus is a custom service there is something that need to be changed, I followed the tutorial about making...
Objective: I want to read 64MB data stored in external flash (interfaced with nrf52840) from android mobile App (specific: One Plus 7T)
SDK: nRF5 SDK v16.0.0
Soft Device...
Dear,
Im trying to measure the RSSI with THINGY:91, I found on the document nrf91_at_commands_v1.1.pdf about
1. AT+CSQ
+CSQ: <rssi>,<ber>
Note: Not detectable, RAT...
Hi!
I am currently working on a project where i would like to use Thingy:91 as MCU board as it contains other features i need to use, like 4G and GPS.
The problem is that...
Hi I'm currently develop new product based on RAK8212. I have problem with reprogramming devices. Programmer i use is nRF52-DK I'm not able to reprogram about 10% of devices...
Hello,
I have a low power application, which is activated by a push button press. (The DC-DC converter is also in shutdown mode normally, so the NRF9160 does not have power...
I am occasionally (very rarely) getting "Mesh assert at 0x00037996", but when I try to look this up, I get:
My understanding is that this means the mesh_assert is...
Hello, this is the nrf52833/52820 design drawn by the customer, because this is our first contact, please help to check whether it is reasonable? thank you.
Hello,
I'm working on a BLE app on an Arduino Nano 33 BLE, which is equiped with an nrf52840. I'm struggling to increase my BLE transfer speed ( i think due to the limitations...
Actually i was working on 3 boards, nRF51422,nRF51822 & nRF52840. While executing some examples on each board i realised that each board has its specific pca hex file to be...
I n the main of my program I have this( UBLOX_PWR_PIN = Pin16 of nrf ),
uart_init(); nrf_gpio_cfg_output(UBLOX_PWR_PIN); nrf_gpio_pin_set(UBLOX_PWR_PIN); nrf_delay_ms(200...
Hello,
I've a problem with a PPK board.
When the current go over 10mA the value reported is wrong, in my case should be 15mA and PPK measure 80mA and more. Instead, in...
Hello,
I am working on a project that is using nrf52840 chip as a peripheral and the product is supposed to last and run for 25 years. During that period the device will...
