Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi,
I use bdb_start_top_level_commissioning(ZB_BDB_NETWORK_STEERING | ZB_BDB_NETWORK_FORMATION) to open zigbee coordinator network.
my question is :
1. Is there any...
Is there any place where you collect information about using your BLE5 chips in smartphones/pads and about relevant plans of such manufacturers or open design projects ??...
Hello guys,
We are using SES and SDK15.3.0. Our SoC is from nRF52840 family. We have a custom board with external QSPI flash memory that we want to use as USB MSC device...
Dear Nordic DevZone,
Greetings! I have been trying to get working with the example ble_app_buttonless_dfu I tried configuring for extended advertising with help from this...
Hi,
I fail receive data from SPI.
I have check the signal from oscilloscope, there slave does reply SPI data to master. So, It is definitely is code problem.
Below is...
Hello,
We are testing ble beacon based on nRF52832. We have incorporated DC-Dc in our design. The design has fractus antenna. Our previous design was without DC-DC. Now...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
Till now we were using nRF Connect app...
Hi All,
I am trying to assemble the ble_app_template project (nRF5SDK160098a08e2) in Eclipse. Has somebody some more detail instructions on how to compile new projects...
Hello,I am new to this field.I dont know how to interface QMC5883L Geo-magnetic sensor which is 3-axis magnetic sensor with nrf52840 and read the temperature and axial(x,y...
Hello,
Could you please help to create a list of reasons (or get a reference to it) when node may fall out from network?
Removing network credentials on the node
Key...
I am getting killed by the fact I cannot restore the CCCDs on a bonded reconnect and need to rely on the client doing it every connection - a violation of the standard.
...
Hi Team,
Please let me know can we register Multiple e-sim in Thingy:91 and nRF9160/DK? What is the procedure for e-sim registration in Thingy:91?
Regards,
Ashiq Mo...
Hi
I am testing the example ¨¨ ble_app_att_mtu_throughput ¨¨ on nRF52840 by changing different paremeters incuding data length, MTU, transmitting power and PHY.
when I...
Uisng pca10040 and SDk16.0.0 + Segger
I built and ran the GPIOTE example so I could experiment.
I want to toggle a gpio once only and then stop and I need to know when...
Hi,
Iam looking for very simple low cost wireless module which supports at least 500meters range ,please suggest a module.
I dont need lora module apart from this please...
