We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi,
I use example nRF5SDKforThreadandZigbeev3209fade31\examples\dfu\secure_bootloader\pca10056_uart to upgrade bootloader and coordinator application.
I try to upgarde...
Hello!
We are trying to get low average current consumption on the nRF9160 DK without success.
The floor current between modem active time is ~60uA, which is fine. But...
We've recently been testing the accuracy of the GPS on our devices. My basic method has been to trigger on GPS_TRIG_DATA_READY/GPS_CHAN_NMEA, and at each trigger fetch both...
I would like to advertise some sensor data (temperature, humidity, pressure, co2, voc and other) by BLE advertising packet without any connection. I know, I can put it data...
How much ram is my application + Zephyr + modem firmware using and how much is available in the nRF9160? I'm unable to find a memory map and anyway that wouldn't include dynamic...
Can we alter the eddystone tlm (telemetry) packet to send custom data . [This is not following the standard packet structure].
But I wanted to know how to alter the given...
I need a product that will allow me to connect a PC to a Bluetooth device through its Bluetooth connection. I will need to be able to send data bytes from my PC across the...
Hi everyone,
I am a beginner with Nordic SDK. I followed the " Getting Started Assistant" and then try to open asset_tracker project on step 4. During the opening I got...
Hello,
The fds.c fds_register() has suspicious usage of atomic variables.
It is first checked if there is space in the m_cb_table, then m_cb_table is modified and only...
Hi, I am trying to add timer information to the sending packet. We created some space(manuf_data) to store data. However, the problem is we do not know how to put actual-time...
Quick Summary: - Devices used: nRF52832 (Central), nRF52840 (Peripheral)
Example based on : BLE Scanner
Hi Team,
In my current application, based on a BLE Scanner Example...
Hi,
I'm using the latest SDK v16. I got the following error when call peer_manager_init()
<debug> nrf_ble_lesc: Initialized nrf_crypto. <debug> nrf_ble_lesc: Initialized...
Is there a recommended way to inspect the state of the heap? I haven't found anything obvious yet. I'd mainly like to know the amount free, the largest block, and perhaps...
Hi,
I start developing with ble_app_template and DK
I combine uart spi twi into it
It can connect to my phone(nRF Connect APP)and work fine on DK
However when i use...
