Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
After reprogramming with mfw_nrf9160_1.2.0 and nrf9160dk_asset_tracker_ltem_2020-04-29_bc7ade8b.hex
the nRF9160 fails to connect properly. LED3 blinks continually, LED4...
Hello,
currently i am using nRF52832 board with Nordic SDK 16.0.0 and softdevice version 7.0.1
i have separated DFU service and bootloader code. added dfu service in my...
Hello all,
I'm still learning C at this point of stage. What I ended up was following a tutorial online on simple BLE project controlling the on-board LED.
The tutorial...
This is a 2 part question concerning the LFCLK input levels as well as how to test the LFCLK frequency against the HFCLK frequency to make sure they are consistent.
In this...
I am currently working on a project using the MAX30102 Heart rate module. This sensor has red & ir led's. I connected the the max30102 sensor to the nrf52 DK as follows VDD...
Hi,
I'm looking at the BLE aggregator example, it uses a service called "ble_agg_cfg_service" .
1. It looks like this service is the same as NUS ?
2. I'd like to...
Hi
I am evaluating the production of a BLE product and your chip solution looks promising.
In my case the bluetooth will be connected to PC and it should be recognized...
There are a number of issues in ble_advertising that relate to changing the status of advertising in response to events. Specifically the current adv mode is not changed on...
Looking at the schematic diagram of the ISP-1507-AX Test Board….
www.insightsip.com/.../ISP1507_AX_TB_Schematic.pdf
… I can see that there is the possibility to connect...
Hi
I am using ble_app_uart code from ble_peripheral folder and nrf_connect app to receive/send data.
I have interfaced external sensor with UART pins and receiving data...
Hi I am using UART code from nRF5_SDK_16.0.0_98a08e2\examples\peripheral.
I have checked loop back with default UART pins,which are 5,6,7,8.
Now I want to interface some...
Hello,
I am using a nRF52DK (PCA10056). When I connect the board, the J-link drive opens up, but it does not detect on nRF Go Studio, nor is it flashing any code. I am using...
I'm using the USB CDC ACM example to write a message to a com port. I can receive messages fine except there is one problem. I am receiving the characters one character at...
Hi,
Is it possible to use two LPCOMPs simultaneously?
I would like to use analog channel 6 and 5 and if I register a RESULT Above on channel 6 it should start a software...
Good day to all
I would like to get a little more information about the function:
added in softdevice version 7.0.1.
Starting the radio in connection mode is shown...
