I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hi Team,
Please let me know can we register Multiple e-sim in Thingy:91 and nRF9160/DK? What is the procedure for e-sim registration in Thingy:91?
Regards,
Ashiq Mo...
Hi
I am testing the example ¨¨ ble_app_att_mtu_throughput ¨¨ on nRF52840 by changing different paremeters incuding data length, MTU, transmitting power and PHY.
when I...
Uisng pca10040 and SDk16.0.0 + Segger
I built and ran the GPIOTE example so I could experiment.
I want to toggle a gpio once only and then stop and I need to know when...
Hi,
Iam looking for very simple low cost wireless module which supports at least 500meters range ,please suggest a module.
I dont need lora module apart from this please...
I have latest SDK, which is nRF SDK 16.00. I have noticed that not all the examples are available for PCA 10100.
So my question is what is the difference between the PCA...
Hi,
I have compilation error to use SPI.
Checking project status Building ‘ble_app_beacon_pca10056_s140’ from solution ‘ble_app_beacon_pca10056_s140’ in configuration...
Hi,
I am trying to get the nRF-IEEE-802.15.4-radio-driver found at GitHub to run on my nRF52840 DK.
Does anyone have a check list or can explain how to link the files...
Hello,
I'm wanting to start a project with the NRF52840 DK in Segger Embedded Studio. I went through almost all of the tutorials and set up the SDK.... etc but I have...
hello.
I used 52840 act as center device.whose RX TX connected to my another MCU(MTK7688 UART). This is a IoT-GateWay. now I want to upgrade the 52840 application. BUT,...
Hi
Two years ago our device was tested using nRFgo Studio 1.21.2.10 Direct Test Mode.
How can I know if the nRFgo software used BLE 4.2 or 5.0 during the tests? The only...
Hello,
We are making a custom application where we have several ble-mesh server nodes (nRF52832), and one of them connects to an Android app, acting as a proxy. The app...
Hi All,
I want explore BLE5 extended advertisement with nRF52832.
Using "ble_peripheral\ble_app_blinky" code from SDK16.0.0, facing " NRF_ERROR_INVALID_PARAM (7)" error...
Hi, I ported the TimeSync example devzone.nordicsemi.com/.../wireless-timer-synchronization-among-nrf5-devices to the current SDK 16.0.0 and S140_nrf52_7.0.1_softdevice. But...
I am unable to set the PA/LNA Mode on NRF52832 using SDK 14.2 ( Soft Device Version S132 5.0 ) using the Fansttel BT832X SoC.
i have used the exact function on the below...
