Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi Team,
I am working on SYSTEM ON mode with Low power mode also called Idle mode in nRF9160 module.
I was able to go to Idle mode with current consumption of 6uA with...
Hello there,
I created a project a while ago with the SES and the SDK 15.x. For a new Project, we would like to move to PlatformIO. Right now I am evaluating where we will...
Hi Guys
I recently made my own PCB for a project. On the PCB I am using a Laird BL654PA Module with external antenna. All the I/O's work great but im struggling with the...
Hi,
We had met problem at buttonless DFU with bonded information at Andriod set-top-box.
The problem we saw is we can not know when the ATT table is different at andriod...
I'm trying to wait on a single POLLIN event on a net socket, but I'm finding that poll() will still return immediately with the POLLIN event even if it's not set in the struct...
Hi , I am developing a zigbee project using nrf52840 using NRF52 zigbee sdk . I had to do some changes in zboss header files ( zb_config_common.h and zb_config.h ) to change...
I'm using the NRF52840-DK with the SB40 jumper cut, then powering through P21 and measuring with an ammeter across P22. USB is unplugged during measurement. I'm using zephyr...
Hi,
Eventhough I am able to communicate with my I2C slave, this message appear for every transmision.
[00:00:00.709,350]
[1;31m<err> i2c_nrfx_twim: Error 195952641...
I get long range demo code for 52840 on the web:
long_range_demo_15.2
and modify the code to test the 52833 long range feature;
MAINLY code:
My question is:...
Hello.
I would like to use UART or UARTE in all of my future projects for debugging. What steps do I need for one app to work? More specifically:
1 - What include folders...
I'm new to the nRF5340 and zephyr and ncs, but I have gone through the tutorial series
We're developing a product that will use the SPIS peripheral on the nRF5340 and...
Hi, Im developing a Zigbee concentrator. I used nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730 ble_zigbee_template as start point of my project. The light bulbs and switch...
We are using Lairds BL652 module in our product and develop code for it using the Nordic Semiconductor nRF5 SDK and flash it using jlink. Referring to the attached schematic...
Hello Nordic,
I recently setup the Command Line application for our device, using USB CDC ACM. I started experimenting in the example cli project. After everything was...
