Retrieving Custom Firmware Version from nRF52 BLE Controller to nRF9160 Host
Product: nRF Connect SDK v2.6.0 Hardware: nRF9160 (Host) connected via UART to nRF52832 (Controller...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Hello all,
I am trying to activate ADC to measure a voltage every few seconds using nrf51822. When it is done, I supposedly deactivate ADC so it does not consumes while...
I am designing an device and i need to communicate with the device using the I2C of my nrf52.
when ever i try to initiate the transfer process using the driver function...
Is there a Peripheral Encryption Example for the nRF52? and can the Master Control Panel tool(3.10.0.14) be used to test the Peripheral Encryption?
If i clcik the down arrow...
Question about usage. I am using the nRF52, and ported product code that was running on the Alpha SDK11 to the release SDK11. I believe that what I will describe is a new...
According to the product specification of the nRF51422 the current between the advertisements is:
i_sleep = I_on + I_rtc + I_x32k
16k Ram enabled: = 2,6 µA + 0,1 µA...
I realize that this code is "experimental", but we are trying to utilize it as a reference and having problems with its stability and scan results.
Specifically, we are...
Hi!
We are currently implementing a time synchronization algorithm using a nRF52s. Currently, we´re getting the min error of 20ms between synchronized slaves. We think that...
I'm using a nRF51 with 32K RAM and SD120. When I started using RTT Viewer I could send data to the terminal, and debug my code. Recently my J-Link plus won't allow me to debug...
I'm trying to secure my peripheral by allowing only bonded devices to connect. I'm using device manager, when I bond a central with nrf master control, the bonding succeed...
Hi,
I'm facing the following issue when trying to use the DFU bootloader. Below you can find the code of the bootloader, which I flash after I erase everything, flash S110...
hii....
i want to make my device connected through a secret pass code (may be six digit)..ie. my device get advertise then when master control panel discover my device...
Hello,
I was just wondering what are the steps to download my software that I made to nRF51422 to the nRF51822. I changed the target device and the memory areas in the...
Hi,
I am using SD 120 9.1.0 and SDK 8 as a central and SD 110 V8.0.0 and SDK 8 as a peripheral.
I have a setup central connects with 8 peripherals. First I had 1 central...
Hi guys,
I'm wondering what is written there in "empty section" between 0x7c0 and 0x1000 address? Are there any special registers (which must not be overwritten)? It looks...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
