I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,
I have a central device and I need to register lot of 128 bit vendor service/characteristics (~20).
However, sd_ble_uuid_vs_add return NRF_ERROR_NO_MEM.
Some post...
HI , Global Tech Tour 2015 - Shenzhen I get the infomation that the R&D in nordic Semiconductor has got the development board NRF52 smart remote. What's the data you will...
Hi All, I'm trying to compile and download sample code "dual_bank_ble_s130".
But it seems fail to run.
I'm using SDK10 examples\dfu\bootloader\pca10028\dual_bank_ble_s130...
can we transmit data of size greater than 40kb (image) through nrf51822 but without connection to peripheral device i am working so hard to find a way but not achieving the...
Hi I'm trying to optimize my connection interval for latency vs power consumption but I notice that a lot of values I try to set are giving me the invalid parameter error...
Hello,
I am using S120 central stack 2.1.0 with SDK 9.0 and able to work with single server connection. Now I am trying to connect to 2 peripherals with 2 different UUID...
I read timer example of SDK7.0/6.0, and found that often we write some code to tigger the clock.
but the same example of SDK9.0 needn't. why ?
the code of SDK7.0: NRF_CLOCK...
Hi,
I am developing ble apps with the BL600.
I am coding a source file with the keil IDE. And this source is deployed to the nRF51 DK board through the nRFgo Studio....
hello,
i am unable to update application or softdevice or bootloader via master control panel 3.9.0
while doing so, it shows error:"FAILED TO OPEN TRANPORT BACKEND". ...
I followed the Nordic Tutorial located here . I'm using a PCA100028 Dev Board, MCP 3.9.0.6, and a Segger J-Link Plus. I'm using Keil uVision5, and used the pack installer...
I have a set of characteristics on my ble peripheral (nrf51) which I display with nordic control panel tool (android). but when I deleted one characteristic on the peripheral...
Hi, I am evaluating the use of Gazell and BLE as a possible solution for my project. I had heard that there was a way to have both BLE and Gazell running on a device at the...
we will do some measurments and answer when we get some time to spare for this. Others are welcome to answer/comment freely about their experiences/knowledge.
I have some custom hardware (nRF51822) with a couple sensors on it and would like to have the data sent via BLE to a smartphone. This may be timer based on triggered by an...
