We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
This ticket is the continuation and related to the previous ticket on the matter: https://devzone.nordicsemi.com/f/nordic-q-a/121669/enabling-the-tls-layer-to-get-a-https...
Hi,
Using nRF Connect SDK 2.7.0 on an nRF9160. Using native tls, works fine, i can setup HTTPS connections.
Problems arise when i try to use MQTT with native TLS (with...
Hello Nordic DevZone community,
I have been working with the ZBOSS stack on the nRF5340 and understand that it has version management and migration features for persistent...
SDK 2.3.0
We have a custom board with a few GPIO connected to various interrupt sources (Button, sensor interrupts, power connection etc.)
We are experiencing here sleep...
nrf52820 custom board
nRF5_SDK_17.1.0_ddde560
s112_nrf52_7.2.0_softdevice
secure_bootloader_ble_s112_pca10100e
I tried to incorporate ble dfu to my application but...
Hi Team,
Excuse me. Where can I find the reliability test reports of the following four models? Thank you!
nRF54L15-QFAA-R
nRF9151-LACA-R
nRF7000-QFAA-R
nPM1100...
Hi all,
I am facing issues when initializing and enabling the Softdevice after using the nrf_nvmc driver to erase and write flash pages. The project shall have the ability...
I am working with a MacBook Pro (El capitan) and the nRF51822 beacon and I need to measure the RSSI. I understand that the app nRF connect can do it, but the antenna on my...
Scenario is as follows:
NRF52 (SDK12.1, SD3.0) works in central and peripheral mode.
What happens is that on start we create a single shot timer with 4.2second to wait...
I write a function, It can read ok without BLE starting.
When I start the BLE , the function can not run.
So I think that , if I can use some function to stop the stop the...
Hi, all.
I tested ble_app_uart in example directory by PCA10040 board.
It works well.
printf ("UART Start!") in main.c works well. "UART Start" string cames out on putty...
Hello everybody,
I have a problem when I try initialize the ANCS service. The method ble_ancs_c_init(); from ble_ancs_c.h return the error NRF_ERROR_NO_MEM.
My configuration...
I flashed the nRF52 DK with the mbed bootloader developer.mbed.org/.../ but I'm having issues with the board. When I drag and drop the file which is a very basic blink program...
Hi,
I was trying to integrate a more simple version of the buttonless dfu example on my application. My first step was to get rid of the peer_manager and also the flash...
What is the use of of PCA10040 chip in NRF52 Development Kit(NRF52832 chipset). ?
Do I need a programmer to program NRF523832 in the DK, Can I just program it through USB...
Hello,
I asked a question after this old one : old one and I read other posts on the subject.
I wonder whether explained constraints may have changed or not since I am...
Hello,
I'am trying to do directed advertisement with NRF51822 (Smart Beacon Kit pca20006). I don't have any previous connection with peer, its address is hard-coded. The...
Hello:
I am writing a BLE profile involving several characteristics. One of the characteristics is an operation code (read/write) tunnel.
Each time a BLE central device...
This situation occured just in Android phone,iphone have not meet this situation.
A detailed description as follows:
After DFU used Android phone,connect again,notify...
Hi, I want to send data from arduino to nrf51dk which will then use uart service to send the data over bluetooth.
I want to use SPI communication between the two microcontrollers...
