Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
Does anyone know of a good OneWire library that works directly with the nRF51 family?
I imagine there are ARM solutions available that could work, but I haven't found a...
Hi,
Hope this is the right place to ask this. I've been trying to reset my password on the nordicsemi.com website but it doesn't seem to work. I receive a mail with my username...
Hi,
I am using nRF52 + Eclipse (gcc) with the ble_app_uart application.
I have an iPhone 6+ with nRF UART app running.
If I send <= 59 characters through the virtual...
Hi, is there an example that show how use the pwm with ble?
i'm new on keil.
i have used mbed until yesterday, the pwm that use keil is a hardware os software pwm?
thaks...
Hello Nordic,
I am following example code [--ble-app-lbs-master] for my application in (keil4.6/sdk8.0.0). Its already consisting (app_gpiote), but I want to add some code...
hello,
I am having some doubts regarding the connection handle. Will it be the same for both devices participating in a connection? I was trying to connect two devices, one...
A call to sd_ble_gatts_service_add(..) is returning fault code 0x3001. Looking at the NRF_ERROR #defines, this seems to mean "STK SVC handler is missing".
Can anyone shed...
Dear ladies and gentlemen,
I can't find this information anywhere. In the datasheet on page 519 - 521, I see that the decoupling capacitor C6 on pin 32 (DEC2) is not mounted...
Hi
Currently I have a device with the following details:
Ic Version - 2,
Variant - CE AA ,
Build Code - D0,
Hardware Id - 004d
I am using the softdevice s110_nrf51822_7...
I am trying to set up an environment based on CMSIS Packs. However, when using some components from nRF_Libraries, these lines get added to RTE_Components.h:
#define GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
I am working on nrf51 iot sdk. I have created a IPv6 tunnel in HE and is able to ping the gateway as follows:
root@raspberrypi:/home/pi# ping6 2001:xxx:18:xxx::1
PING...
Hi,
I already used the sd_ble_uuid_vs_add for adding my base UUID in the internal table and it return a valid uuid_type (in my specific case it's 0x06).
I need to add...
I am using SDK 9.0.0 and i am having a doubt in bsp.h.In this header file when gone through this part of the code
#if (LEDS_NUMBER > 0) && !defined(BSP_SIMPLE)
#define...
