I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
The peripheral is actually a dual-mode device, with BLE being a peripheral device.
I can connect to this device and discover the GATT services with the nRF Connect iPhone...
What is the minimum and max value that the NRF_RADIO->TXPOWER register can get set to? The datasheet it takes a signed 8 bit for the setting, but what happens if you set it...
Hello,
I am trying to read data from nRF51422 ADC using SDK51 PCA10028 board downloaded with S130. I tried one of existing ADC with Softdevice examples, it seems to work...
I have meander antenna design on my board with matching network(similar to PCA10031).
Since I don't have access to VNA or Spectrum Analyzer for tuning antenna, I am tuning...
I'm building some code off of the twi_master_using_app_twi example which is available in the SDK (v11.0.0).
The two peripherals I'm working on are an accelerometer (LIS3DH...
I've just upgraded to Windows 10, and I've found that the PC freezes completely (i.e. no mouse movement, no keyboard response) when I unplug an nRF52 DK board. When I plug...
Hi,
In my application, I need 3 PWM to drive LED. Each PWM will have the same frequency but not the same duty cycle.
Is that possible to do that?
I know that Timer0 is...
hi
on android side of my project i try to disconnect from gatt by this code
mbluetoothGatt.disconnect();
but in nrf51422 this event not trigering
static void on_ble_evt...
Hello, I am working on low power modes and I got trouble finding the code to switch from NRF_POWER_MODE_CONSTLAT and NRF_POWER_MODE_LOWPWR. Can anyone please guide me to better...
Bonding causes power consumption to rise.
I have a central and peripheral device communicating using the nus-service. The peripheral device is running FreeRTOS with tickless...
Hi,
I'm trying to test the DFU over HCI included in the SDK examples but I can't make it work. This is all the information of the environment I'm using:
SDK: 10.0...
Condition: nRF52, SDK11,s132, SDS v2.0.
Using the sd_ble_gatts_hvx() in timer1 interrupt service(timer1 interrupt priority is set to level 3) will result in hardfault. While...
I am using SDK_11 s130. I am looking at app_error_fault_handler() in app_error_weak.c
Inside app_error_fault_handler(), there is this line of code;
UNUSED_VARIABLE(bsp_indication_set...
Hi,
I am using keil uvision 5.17, SD 130, nRF 51822, dualbank bootloader.
I have programmed own application and merged bootloader, application, soft device.
I...
I am using ble_app_gls on SDK_11 s130 on nRF51-dk.
This is a follow-up question to the question below.
devzone.nordicsemi.com/.../
After enabling debugging, I discovered...
