This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I am using nrf51822 as a central device that is trying to connect a peripheral device nrf8001.
I want to build communication bewteen them and use nrf51822 to receive the...
Hi,
I have a small question regarding flash write/erase cycles and I was unable to find a clear answer.
I can see in NRF52 specs:
Flash write/erase cycles: 10...
Hi,
I've been trying to get DFU updates working on my device for a while now... I've got the single-bank bootloader compiled and seemingly working (and a combined hex file...
how to modify ble hand shake time which normal connect to phone.
this scene the ble board has connect to the phone, but need down scoping the ble time to let the 2.4G work...
Hi,
I would like to save some data from characteristic into the Flash. Due to this fact I decided that I will use scheduler. When the value of actual characteristic is...
We are trying to complete Bluetooth qualification on our Cycling Power Service (CPS)
against the Bluetooth Test Specification (Document Number CPS.TS.1.1.0).
We fail the...
Apparently, the dfu bootloader example in nrf51 SDK 8.1 is not working on PCA10031 type(16K RAM devices). In my case, the device is RedBearLab BLE Nano and nrf51822.
Can...
Hello,
because of my mistake, rx tx pin was not cross connected.
So i want to swap rx tx pin on nrf51822.
In the example ble_app_uart_s130_pca10028, i change the code...
I used the example in nRF51_SDK_9.0.0_2e23562\examples\dfu\experimental, the first time that work well. But when I want to update a app in app(with dfu function),it failed...
Sir,
Can someone tell me what all things I should remember while I am trying to execute a project which is developed in sdk6 to be excecuted in different sdk file(maybe...
Hi, i'm using a code to save 4 bytes on the flash memory and it works. In, fact i checked the data address concerned using the keil and i see the changes when i write and...
I can send a CR terminated string through the UART using tx fifo OK.
BUT, if I receive a string from the UART rx OK first, and then try to send a string, only the 1st character...
Canyou please tell me how to do , to save correctly 4 bytes in my program that uses flash memory for bonfing. i have how to save 4 bytes function seperatly, and my program...
Ported the hrs_rscs relay central-peripheral app with peer mgr to custom platform with mutliple peripheral devices, and it has been working very well. The last step is to...
