Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Still trying to get anything ta all to work on the nRF52-DK
I erased the chip
I flashed the soft device "soft_device_s132_v3.3.3" to address 0 and verified
built...
Hi!
We are having problems with pairing & bonding procedures with iOS devices.
On the peripheral side we are using a nrf51822 BLE module on which we are testing pairing...
Hi all,
2 days before we bought nrf52832 board.
in new board i can able to execute all peripheral example ( LED BLINK,button,uart,timer..)which doesnt need softdevice...
I'm trying to setup the RTC in the nRF52 to count with a resolution of 1mS. As the count has only a 24 bit value, I wish to clear the count every hour to start again.
There...
Hi all,
I'm having a error on my code, and wanted to understand it better. I'm using a custom board with a Rev.3 CTAA chip, 256k Flash and 16k Ram. I have BLE initialized...
I measured my Nrf51822 current:
when my VCC is 3.0v ~ 3.3v
my current is 0.16 mA.
when my VCC is 2.6v ~ 2.8v
my current is 1.5 mA (why?)
when my VCC is lower than 2...
I have issue with nrf51 booting, i noticed that sometimes when i plug the power to (VDD and GND) the system dosent turn on at al.
1 - how does the system the whole system...
amigos de habla hispana estoy comenzando con este circuito.
mi duda es cual compilador utilizo para crear un simple led blink..
tienen algun tutorial en que me puedan a...
Hi.
I am using the nRF52 Preview Dev. Kit to send data over multiple channels by
setting the NRF_RADIO->FREQUENCY register to the desired frequency value.
To make it work...
Hi,
I am trying to measure the temperature using sht21 sensor with nrf51822. I am using TWI to do this. When I try to send a data to the sensor the application cannot do...
Using the nRF52832 and SoftDevice s132.
If the application code disables the SoftDevice, then the application CAN erase UICR memory in the nRF52832 device.
The question...
I control a module over UART using app_uart_fifo. This module is controlled from nRF host by commands to perform things. This generally works fine but however, sometimes when...
Hi,
I write a code for the max6657 temperture via modifying the SPI MASTER Example. The function for reading max6675 via SPI is shown as follow
uint16_t readCelsius(void...
Dear Nordic Team,
Thanks for supporting.
How to calculate the battery voltage level from Eddystone TLM. Its always transmit 240mV.
I am using CR2302 3V battery.
...
