Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
hi i am using nrf51 development kit. i have gone through nordic development zone tutorial to use Eclipse IDE. build was successful it is creating release folder in which i...
We are interfacing serial flash using SPI interface and use nordic nrf52 nrf_drv_spi.c as the library.
We have taken a look at nrf_drv_spi.c, and it seems in the api nrf_drv_spi_transfer...
I am using Nordic nRF51 Development Kit with SoftDevice_130_2.0.0.I tried to run the SDK 11.0.0's example "examples\ble_peripheral\ble_app_gls\pca10028\ser_s130_spi" from...
As Nordic newsletter, s132 v3.0.0 softDevice have been released, I have a question that: if I want to use new feature in s132 v3.0.0 like DLE or privacy, does Nordic need...
I am trying the tutorial Radio Notification and was following the patch from Ble_radio_notification wont compile . The radio notification init comes right after the ble enabling...
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 board. I want to know how to control the timeout from when the program goes from Bootloader...
My set Up:
TI as Peripheral,
Android as Central,
Nordic as Central
I am doing directed advertisement using TI as peripheral.
Using Andriod as central, I am successfully...
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 board.Using the OTA Tester (s210), I am currently doing an OTA Update with the s210 dual bank...
Hi all,
I have an STM32 connected to an nrf51822 via uart, and I want to do a firmware update of the stm via ble.
Therefore, I would like to take advantage of the Master...
Hi
my idea is to open and close pipes identified by BLE address of device.
Currently I enable ESB on BLE disconnect using timeslot API.
How can I do this "on the fly...
I'm testing with Soft Device 8.0.0, ble dfu operation with single bank, nRF toolbox on Android version 1.13.1 (installed on 5/11/2015). I generated a zip distribution file...
Hi,
is there any way to connect at the same time multiple devices with Android/iOS nRF UART app to an nRF52832 with ble_app_uart example?
I was thinking about adding advertising...
HI all,
I am setting these parameter as follow in my ble_app_template sample.
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(7.5, UNIT_1_25_MS) /**< Minimum acceptable connection...
Hello everyone
I'm the proud owner of a nRF52 Prev. DK and trying to get my project to work. I would like to sample 3 to 5 analog signals using the ADC on the DevKit, followed...
