Hello,
I'm developing my custom sensor application. It's a matter over thread device. Before final product I'm working on a NRF52840 DK PCA 100056 v3.0.1 and NCS 3.02. It...
Hello!!
When I'm reading carefully about the nRF7002 Power save operations, It's hard to understand about Power save Exit Strategy.
https://docs.nordicsemi.com/bundle...
Hello,
I higly need to run twister unit tests in debug mode with breakpoints, step by step, spies and other debug tools in vscode. I did not find a way to do so.
Is...
Dear devzone, Can our nRF52840 detect 20 nanosecond voltage fluctuations using COMP? For example, if I set a lower threshold of 20mV and an upper threshold of 60mV, and the...
Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
I'm using the nRF52840-DK part number 1490-1072-ND I ordered last week. In both nRF Connect for Desktop and the VS code extension the device wasn't able to detect. Tried two...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
I used SDK15 and ble_app_uart_c.
I start a UART timer sending and start a LED timer. There is a probability of app: SOFTDEVICE: ASSERTION FAILED in the process of running...
Hello all,
I'm using the Nordic SDK 14.2 BSP button handler. I have a push, release, and long push event on a single button. These are working as expected -
Except when...
Hi all
I am using the spi0 to storage the data and twi0 to get sensor data . But after I add the file nrf_drv_twi.c and compile , it complies wrong :.
\_build\nrf51422_xxac...
I have problems with disconnecting my Android devices from my BLE peripheral. I don't think this is Nordic-specific, but perhaps someone has an idea?
Disconnecting using...
Hello,
i have a application with two operating states state1: device is in deep sleep state 2: device is running
i wake up the device from deep sleep via gpio interrupt...
Hi
I am integrating your Android DFU library with our mobile app to do FOTA to our Nordic device nRF52832 . We are using SDK 14.2 and doing the firmware update using zip...
I have the nRF51-DK and have installed Python etc. and the nrf_sniffer_2.0.0-beta-1_51296aa.
3 .hex files are in that installer: sniffer_pca10028_51296aa.hex, sniffer_pca10031_51296aa...
Hello,
I'm trying to shutdown my whole system (nRF 52832, SD132, SDK 12.3) after advertisement fast and slow are finished, following the structure of the peripheral BLE_APP_UART...
Hi,
I am trying to run lightswitch example in MDK.
Provisioner keep logging : 419, Unhandled Mesh Event: 4
Button 1 is in on state.
and LD5 is keep blinking.
these...
Hello. I'd migrated my application on SDK 15.1 from 14.2. The firmware of my product is always updating so I use NRF LOG module to debug it and see what is going on in every...
Hi to all,
recently i bought PCA10059 board, but i have problem in programming it. because i had some experience with NRF51 and NRFGO, at first when received the board i...
Dear Nordic,
I am using nRF52840 chip for BLE Advertising I want to encrypt this Advertising
I Read a CCM-AES encryption in BLE is it right way to this 31 bytes advertising...
I want to sleep at the lowest current level possible while retaining RAM. I see that I(ON_RAMON_GPIOTE) is 17.37uA! I want to avoid that. I see I(ON_RAMON_GPIOTEPORT) is only...
