Hi! It seems that I may have uploaded a non-working application to the Thingy91x. Therefore Device is not conectable via USB. The device is responding only in "MCUBOOT" mode...
I have an external GPS module connected to an nrf9151dk over UART. The module is correctly powered, and sending messages over its tx pin, which has been confirmed by attaching...
I´m trying to change the installation path of the Nordic Power Profiler as I´m running out of space.
I have about 9GB left, but when trying to open a captured file, Power...
Hi Nordic team,
I’m working on a custom LoRa interface using the Thingy:91X, and I’d like to know whether the Qwiic connector pins (P0.03 – SDA, and P0.04 – SCL) can be...
Hello,
I would like to measure the current consumption of my nRF9161 and compare the result with a standard measurement. While searching in your documentation, I found this...
Hello,
Does the nrf_oberon library support the nRF54L series parts? In the technical documentation, it appears that M33 parts are supported: https://docs.nordicsemi.com...
Hello,
I am using nRF5340 DK, I was trying to connect it to my laptop MacBook Pro M2 but I continuously get this notifications about JLink disconnecting and reconnecting...
hi, nordic team:
Now I am using the nRF5 AirFuel SDK version 2.2.0 to develop the PTU and successfully use the serial to do the dfu function.
I used nrfutil for DFU, but...
Hello, I trying to debug with GDB server Because of this .
I open the GDB server like this
go to build directory and write client cmds below
output is $4 = {<error...
SDK12.30 supports S132 V3.0. Is there any other version SDK supporting S132 v3.1?
Any problem for firmware built with S132 V3.0 and running on module with S132 v3.1?
Hello,
I've disabled the buttons in light_switch example for the client DK. I'm using GPIOs for input and I want to enable BSP_BUTTON_3 to reset mesh network configurations...
After switching to SDK 15 from SDK 14, stopped working correctly transmission of HID Report Descriptor over USB, what in case leads to incorrect device enumeration.
Now...
I'm developing a database with FDS that stores application-level data that must be able to be matched to bond data. After looking at the files for Peer Manager, ID Manager...
Hi All,
What is the recommended way to choose FIFO and buffer sizes for the nrf_serial module? I mean the optimal values for the following constants:
SERIAL_FIFO_TX_SIZE...
Hi,
the pull-up resistance Rpu of GPIO pins as stated in Product Specification v3.1 in Table 62 is supposed to be 13 kOhm (typ). Since we measured a different value on pin...
I started development with the S132 (SDK 15.0.0) peripheral example "blinky". After some modification, it handles all necessary communication with my phone flawlessly. Now...
I'm attempting to use the USB MSC example (from nRF5 SDK v15.0.0) with external flash chip replaced with Winbond W25Q128FV and I see the following logs:
[00:00:00.000,000...
Hi,
I have designed a customized for nrf52832 with a trace antenna. I haven't used any low pass filter and made the changes inside sdkconfig.h file to use RC and that board...
Hi,
I'm using nrf51822 module purchased from www.waveshare.com/core51822.htm . I'm running uart over ble application example. I commented uart_init() function in main(...
Hi,
I have the following setting. I have a dongle with with a nrf52 which sensd all data received from the NUS service to the host via a uart and a FTDI. The FTDI is capable...
Hi.
I want to implement multirole on the nRF52832. I want to advertise beacon data while scanning. So, I modified ble_app_uart_c in the ble_central example. Below is a description...
Hello,
I would like to disable and enable the nus_data_handler in my code to work with several interrupts, so I need to disable that handler and then reenable that again...
