Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
nRF52832, SDK17.1, s132 I work with SPI and it works on the this project with SDK15. But I have transferred this prj to the SDK17.1 and I can't make SPI work. I don't get...
We have a product which is based on nrf52840 and nrf connect sdk 2.8.0
After OTA sometimes, I find that the NVS is erased, which could lead to some issues on client side...
Hi,
I am trying to use mcuboot to load a version that is stored in my external flash, and I cannot get it to boot. My project is being built using sysbuild and my target...
Hello, I am working on a project using zephyr as well as the nrf5340 MCU. For this test, I am on the nrf5340dk. My application requires I drive a PWM at 125khz. In my device...
I opened up the nRF Connect for Desktop application and noticed a new version for the SDK , 3.0.0. I also noticed that the application is being deprecated.
Inside of Visual...
I am trying to get my nRF9151DK connected to Azure IoT Hub. I have used the Azure IoT Hub sample, with some modifications to use LTE instead of WiFi which does not seem supported...
Hello, So I am working on implementing Bluetooth DFU OTA capabilities to send an image from a 54L15, acting as an SMP Central Client, to another 54L15, acting as an SMP Server...
I would like to use native CMake rather than West to take advantage of CMake Presets.
I have been able to make this work on the command line using the following command...
Hi , am developing the st7789v_minimal_sample application using Nrf52840. after creating minimal application am facing some unrecognisable issue. which am stuck can you please...
We have encountered a problem in using iic to communicate that the delay cannot be removed.
We are using the sample in NCS,
the address of the sample is C:\ncs\v2.6.1...
Hi,
I switched to SDK 3.0.0 and got back problem, that I had some time ago with 2.6?? When my code compiles, but controller stuck after many successful builds and I open...
C:\ncs\v2.6.2\nrf\samples\nrf5340\empty_app_core>west build –b nrf5340dk_nrf5340_cpuapp –p
while building the image, getting error:
ERROR: source directory –b does not...
Hi,
I got my hardware modification which added the nRF21540 to our system more or less running under NCS v2.9.0.
Currently, I have the following FEM and antenna configuration...
While using PAWR, we see the above HCI event.
The subevent data is then empty.
Do you have any advice for debugging this?
There doesn't appear to be any helpful logging...
