I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
nrfutil install fail.
I want to update with BLE secure OTA, so install the nrfutil tool. and run the command as following:
but report download pc-ble-driver-py 0...
Total noob here using SES on a Mac to build BLE peripheral (S110) firmware for an nRF51822-based device with SDK v15.
So far I've been able to get the generic portions of...
Hi,
I'm developing on nrf52810 using the SDK14.1.0 and I've take as starting point a template application that targets nRF52810 running on the nRF52 Development Kit. But...
Taking a look through the SDK, there are very few examples using the dongle. I've tried building some of the existing examples by changing the board definition in the preprocessor...
I have a porject working well with normal ble function such as ancs and other services（use sdk15.0） , when I add the mesh model light switch on_off (source code copy from...
Hi.
I applied https://github.com/crfosse/Thingy-52-to-nRF52xx project for get thingy motion data by nRF52840.
But It still found 6 Service for motion service,...
I have a use case where I need to send a sequence of 2 byte bursts as SPI master. The data is generated on the fly and the algorithm would be able to saturate the 8Mbit/s...
Hi,
I just installed nrf connect 1.1 on my Dev-PC (many versions of J-Link and nrfjprog) everything works fine. The visualization of Secure-DFU-Upload-Speed is really nice...
SDK version: nRF5_SDK_15.0.0_a53641a
Softdevice version: s132_nrf52_6.0.0_softdevice
PDK: PCA10040
I am trying to read the ADC pin value using the SAADC module, I...
Hi, I'm using external board with nRF52832. (SDK 15.0.0)
In my external board, there are no RTS,CTS pin. So I don't use hardware flow control (HWFC).
The problem is, I...
How do I add a 128-bit UUID?
I am using SDK 14 and see hardly any examples of how to put a 128-bit UUID in my advertisements.
The only relevant example I found is under...
I am trying to package a firmware update and flash it over BLE DFU and I keep getting the following error on the nRF Toolbox app:
"Upload Failed: Unknown Command"
I cannot...
So, I am using the NRF51 as a SPI slave for an RPI3B+. On a l ogic analyzer and O-Scope the Pi is sending its MOSI SPI data perfectly fine. On top of this issue the nrf_drv_spis_buffers_set...
